GT24UHD-TM skeneris – UHD ClearVū galinė lenta

The Garmin GT24UHD-TM transducer is designed to be mounted on the transom of your boat or on a trolling motor. Mounting hardware for both options is typically included.

For transom installation, you will need the following tools:

A No. 2 Phillips screwdriverA drillBits: 4 mm (5/32 in), 3.2 mm (1/8 in), and 25 mm (1 in)Masking tapeMarine sealant

Transom-mounted transducers like the GT24UHD-TM are compatible with all hull materials. However, for optimal performance, they are not recommended for sailboats due to excessive heel, nor for hulls with chines.

To reduce interference with the depth sounder signal, it is recommended to mount it away from common sources of interference. These include:

Propellers, to avoid propeller wash.Electronic devices such as engines, radar, and audio equipment.Hull features (chine lines, strakes, ribs) that can create turbulence.Other transducers (mount them at least 60 cm apart if they operate at the same frequency).The vessel's machinery, wind, waves, and rain.It is also advisable to ensure proper grounding of the sonar device and other equipment.

Transducers mounted on the transom like the GT24UHD-TM perform best at speeds below 34 mph (approximately 55 km/h) and when installed away from turbulence.

Yes, if your boat spends a significant period in the water, it is recommended to apply water-based antifouling paint to the depth sounder and mounting hardware to prevent marine growth. Before application, lightly sand the depth sounder and hardware with a fine abrasive pad, then clean them with isopropyl alcohol.

Caution: Do not use acetone or acetone-based products on the depth sounder, as this will damage the plastic housing.

The depth sounder must be mounted as close as possible to the centerline of the transom, but at least 38 cm (15 inches) from the propeller. It is critical to mount it away from the propeller wash to avoid interference and potential damage to both the depth sounder and the propeller.

If your propeller turns clockwise when the boat is moving forward, it creates turbulence on the port (left) side. In this case, you should install the depth sounder on the starboard (right) side of the boat, facing forward.

If your propeller rotates counterclockwise when the boat is moving forward, it creates turbulence on the starboard (right) side. In this case, you should install the depth sounder on the port (left) side of the boat, facing forward.

The transducer should protrude by about 3.5 mm (0.125 in) below a fiberglass hull or 10 mm (0.375 in) below an aluminum hull. The goal is for it to be parallel to the waterline and in direct, unobstructed contact with smooth water for optimal performance.

No, it is strongly discouraged to cut the cable of the transducer. Cutting the transducer cables voids the product warranty.

Route the depth sounder cable away from ignition wires, battery and service wires, trolling motor wires, and high-energy wires such as those for radar, audio amplifier, and autopilot pump. If the depth sounder cable must cross a power cable, orient the cables at 90 degrees.

After installation, test the transducer in open water, free of obstacles. Power on the chartplotter and drive the boat at low speed, then gradually increase. Observe the chartplotter. If the sonar signal is suddenly lost or severely degraded, note the speed at which this occurs. Return to that speed and make moderate turns in both directions while observing the chartplotter. If the signal improves while turning, adjust the transducer so it protrudes 3 mm (1/8 in) further below the transom. Repeat until the degradation is eliminated. If the signal does not improve, move the transducer to another location on the transom and repeat the test.

Yes, it is necessary to update the software of your Garmin chartplotter when you install this depth sounder. For update instructions, refer to your chartplotter’s user manual.

Yes, the GT24UHD-TM transducer is designed to be installed on a trolling motor. The kit includes the mounting hardware required for this configuration.

To mount the depth sounder to the trolling motor, insert the hose clamps through the sounder bracket slots until equal lengths protrude on both sides. Position the bracket against the trolling motor body with the narrow end of the sounder facing away from the propeller. Secure the hose clamps around the trolling motor body and tighten them. Adjust the sounder so it is parallel to the bottom when in use. Use waterproof tape (not included) to secure the sounder cable to the trolling motor shaft, avoiding pinching or sharp bends.

Yes, the transducer is supplied with a mounting template in the product box. It is recommended to use this provided template rather than printing your own, as an incorrect printout could result in an incorrectly sized cutout on your boat's mounting surface.

The "UHD" in the GT24UHD-TM name stands for "Ultra High Definition." This indicates that the transducer is capable of delivering highly detailed sonar images, providing exceptional clarity below and to the sides of the boat, particularly with Garmin’s ClearVü technologies.

Yes, transducers mounted on the transom like the GT24UHD-TM are suitable for towed boats, especially when used with an optional foldable bracket. However, they are vulnerable to external damage from trailers or underwater obstructions, so caution is advised.

The Garmin GT24UHD-TM transducer is primarily designed for mounting on the transom of your boat. It is secured to the outside of the transom using a bracket and screws.

Additionally, this transducer can also be installed on a trolling motor. For this, it is fastened to the motor body using hose clamps (not included for electric motor mounting).

For both mounting types, it is critical to follow the installation instructions to ensure optimal performance and avoid interference.