Išmanioji skersinė 150 W 0°-12° (NMEA 2000) jutiklio sonda

The Garmin 010-00701-00 transducer is an Intelliducer through-hull model that provides digital depth and temperature data. This information is directly displayed on Garmin displays compatible with NMEA 2000 network connections.

This Garmin transducer operates at 150 W power and 160 kHz frequency.

The Garmin 010-00701-00 transducer provides accurate depth readings down to 274 m (900 ft).

An Intelliducer is a smart transducer that integrates the electronics required to process depth and temperature data. With its NMEA 2000 connection, it sends this information directly to your boat’s network, eliminating the need for a dedicated depth sounder module. Data is displayed on compatible Garmin displays.

The standard packaging of the Intelliducer through-hull transducer includes the upper and lower parts of the transducer, a gasket, a locking ring, an NMEA 2000 cable, and an NMEA 2000 T-connector.

This transducer is specifically designed for fiberglass and metal hulls. It must not be installed on a wooden hull.

The required hole diameter for installing the Garmin 010-00701-00 transducer is 51 mm (2 inches).

The Garmin 010-00701-00 transducer uses a NMEA 2000 interface to connect to your boat’s network. It comes with a NMEA 2000 cable and a T-connector for easy integration.

This transducer features a tilted element specifically designed to compensate for hull angles from 0 to 12 degrees, ensuring optimal reading accuracy.

No, the 010-00701-00 transducer is an NMEA 2000 model. It is designed for a modern network architecture and is not compatible with NMEA 0183 systems.

This transducer must not be installed on a wooden hull. Installing it on a wooden hull can damage the transducer and potentially the boat due to wood swelling.

To choose the best location, install the depth sounder as close as possible to the keel, away from obstructions (propeller, shafts, other machinery, other transducers) and water intake or discharge openings. The transducer must remain permanently submerged and accessible from inside the boat. Allow a clearance of 200 mm (8 in) above and 150 mm (6 in) around the transducer.

The required tools include a digital inclinometer or spirit level, safety goggles and a dust mask, a drill with bits, hole saws (for a 51 mm hole), sandpaper, mild detergent or a weak solvent (such as isopropyl alcohol), marine sealant, cable ties, and water-based antifouling paint (mandatory for saltwater installations).

For a fiberglass hull with a core, it is crucial to seal and reinforce the core to prevent water infiltration. After drilling the hole, the core must be sealed and reinforced either with fiberglass and resin, or with casting epoxy resin. This ensures the hull's integrity and the boat's safety.

Use marine sealant rated for underwater applications. Examples include 3M - Fast Cure 5200 or Boat Life - Life Seal.

After installation and complete curing of the sealant, launch the boat and immediately check for any leaks around the installation. If no leaks are observed, it is recommended to inspect the installation every hour for the first 24 hours to detect any microscopic leaks.

Yes, applying a water-based antifouling paint is mandatory for installations in saltwater to protect the transducer from marine growth and ensure optimal performance.

The hull deadrise angle is critical. This transducer is designed for angles from 0 to 12 degrees. If the deadrise angle of your hull does not match this specification, depth readings will not be accurate. It is important to measure this angle with an inclinometer or digital level before installation.

Inside the boat, you must allow a clearance of 200 mm (8 inches) above the transducer and 150 mm (6 inches) around it. This space is required to accommodate the internal unit housing and allow for rotation and connection of this unit.

This Garmin through-hull transducer is specifically designed for fiberglass and metal hulls. It must not be installed on a wooden hull, as wood swelling could damage the transducer and compromise your boat’s watertight integrity.

For correct installation and accurate readings, the following main requirements must be met:

Hull deadrise angle: The transducer is optimized for deadrise angles from 0 to 12 degrees. It is critical to measure the deadrise angle at the chosen installation location to ensure it falls within this range. Failure to comply will result in inaccurate depth readings.Drilling diameter: A 51 mm (2 in) hole is required for transducer installation.Location:Install the transducer as close as possible to the keel.Avoid obstructions and interference sources (propeller, shafts, other machinery, other transducers, cables).Do not mount it near water intakes or discharges, behind fittings, strakes, or hull irregularities.The transducer must remain fully submerged at all times during use.Ensure sufficient access to the transducer from inside the boat (approximately 200 mm of vertical clearance and 150 mm of surrounding space).Sealing material: A marine sealant suitable for below-waterline use (such as 3M Fast Cure 5200 or Boat Life Life Seal) is required to ensure a watertight installation. This sealant is not included with the transducer.Network connection: The transducer connects to your existing NMEA 2000 network. It is supplied with an NMEA 2000 cable and a T-connector to facilitate this connection.For boats exceeding 25 knots (approximately 46 km/h), professional installation is recommended.