Lynx skirstytuvas 1000 DC M8

The Lynx 1000 DC M8 busbar distributor is a key component of Victron Energy's modular Lynx busbar system. It integrates a positive and a negative busbar. The positive section provides four connections protected by MEGA fuses (to be purchased separately) with a fuse status monitoring function. The negative section has four connections and one ground connection, all with M8 terminals.

The Lynx distributor provides four positive connections protected by fuses and four negative connections. It also features a separate ground connection.

The Lynx M8 power distribution block is designed to accept MEGA-type fuses. These fuses must be purchased separately, as they are not included with the distribution block.

No, the Lynx power distribution block is designed to accept MEGA fuses, but these must be purchased separately and are not included with the module.

The Lynx distributor is supplied with a 40 cm RJ10 cable. This cable is used to power the Lynx distributor and also to transmit data, including the status of the fuses, when connected to a Lynx Smart BMS.

The Lynx distributor features four status LEDs for the fuses, one for each positive connection. It monitors each fuse and will detect if a fuse is blown, signaling the status via these LEDs.

The M8 or M10 designation refers to the busbar connection joints where the Lynx modules are connected to each other. The specific product, the Lynx 1000 DC Bus Distributor M8, uses M8 busbar connections. The fuses and cable connections on this distributor are also always M8.

Yes, the Lynx distributor’s negative busbar has a dedicated earth connection in addition to the four standard negative connections.

The Lynx distributor is part of a DC distribution system that typically supports system voltages of 12 V, 24 V or 48 V. The battery voltage range supported by associated components such as the Lynx Smart BMS is 9 to 60 VDC.

The Lynx distribution block is a key component for protecting and managing DC circuits within the Lynx modular distribution system. It distributes DC power to multiple devices while individually protecting each circuit with fuses and monitoring their status.

Yes, the Lynx distributor is fully compatible with the Lynx Smart BMS. When connected to a Lynx Smart BMS, up to four Lynx distributors can send information about their fuse status to the BMS. This data is then accessible via the VictronConnect app or a GX device.

Yes, if the Lynx distributor is connected to a Lynx Smart BMS, you can monitor its fuse status via a GX device (such as a Cerbo GX). This allows local or remote monitoring via the VRM portal.

Yes, if the Lynx distributor is connected to a Lynx Smart BMS, it can be monitored and configured using the VictronConnect app on your smartphone or tablet.

No, the Lynx distributor’s fuse status monitoring feature is not available when the distributor is connected to a Lynx Shunt VE.Can. This feature is only enabled when connected to a Lynx Smart BMS.

Up to four Lynx distributors can be connected to a Lynx Smart BMS to send data on the status of their fuses and enable their monitoring.

Yes, the Lynx distributor can be used alone to provide fused DC distribution. However, to enable advanced fuse monitoring via the VictronConnect app or a GX device, it must be connected to a Lynx Smart BMS.

Before working on the Lynx distribution system, it is crucial to ensure that the busbars are not live. Disconnect all battery positive poles before removing the Lynx front cover. Only qualified technicians should work on batteries, following the safety warnings indicated in the battery manual.

Lynx modules are designed to be mechanically interconnected via their busbars. They can be mounted side by side to form a compact and modular distribution system. The Lynx M8 distributor uses M8 busbar connection joints for this interconnection.

To connect DC cables to the Lynx distributor:

Positive cables are connected to the four positive terminals protected by fuses. Negative cables are connected to the four negative terminals. A dedicated ground connection is also available. All these connections use M8 terminals.

The Victron Energy Lynx 1000 DC M8 distributor is a key component of the Lynx modular busbar system, designed for DC electrical distribution.

It includes a positive and a negative busbar:

The positive busbar has four connections protected by MEGA fuses (sold separately). These connections feature fuse status monitoring.The negative busbar provides four connections for equipment and one ground connection.This module comes with a 40 cm RJ10 cable for power supply and data transmission. When connected to a Lynx Smart BMS, the distributor can send fuse status information. This data is accessible via VictronConnect or a GX device (such as a Cerbo GX), enabling local or remote monitoring via the VRM portal. Note that this monitoring feature is not available if the distributor is connected to a Lynx Shunt VE.Can.

The Lynx distribution system, of which this distributor is part, is rated for 1000 A. This specific model uses M8 connections for fuses and cables.