Sondi GT12M-THF 20° läbiv – CHIRP keskmise sagedusega

The Garmin GT12M-THF transducer is made of brass and is designed to be installed on fiberglass, wood, or composite hulls.

This model must not be installed on aluminum or steel hulls, as this would create galvanic corrosion that could lead to water ingress around the transducer.

For installing the GT12M-THF transducer in a fiberglass hull (solid or cored), you will need to drill a 73 mm (2 7/8 inches) hole using a hole saw.

The choice of mounting location is crucial for the performance of the transducer. Here are the main considerations:

The transducer must be mounted in an area where the water is clean and non-turbulent, away from turbulence generated by propellers, keels, seams, fittings, water intakes or outlets.Avoid areas where the transducer could be damaged during launching, hauling or storage.On outboard or sterndrive motorboats, mount the transducer in front of and near the motor(s).On inboard motorboats, mount the transducer in front of and away from the propeller and the propeller shaft.The axis of the transducer must be parallel to the bow-stern axis of your vessel.

Yes, it is mandatory to update the software on your Garmin chartplotter display when installing the GT12M-THF transducer. This update ensures optimal compatibility and the best performance from your sonar system.

The Garmin GT12M-THF transducer is made of brass. This material makes it ideal for installation on fiberglass, wood, or composite hulls.

Cutting or splicing the depth sounder cable is generally not recommended unless you are connecting it to a "black box" fishfinder that requires bare-wire connections.

Cutting the depth sounder cable outside of this specific case may void your warranty. It is important to route the cable carefully, avoiding sharp bends or excessive tension to prevent damage.

The Garmin GT12M-THF depth sounder is made of brass.

The GT12M-THF transducer is designed to be installed in fiberglass, wood, or composite hulls.

No, it is imperative not to install the GT12M-THF transducer on an aluminum or steel hull. Installing this brass model on a metal hull would create galvanic corrosion, which could lead to water ingress around the transducer.

The GT12M-THF transducer is a 20-degree model, ideal for hulls with a deadrise angle of 17 to 24 degrees. For optimal performance, it is essential that the transducer angle matches the hull deadrise angle as closely as possible at the installation point.

Before drilling holes in the hull, you must check the deadrise angle at the installation location. You can measure it using a smartphone app, an angle finder, a protractor, or a digital level. You can also ask your boat manufacturer for the deadrise angle at a specific point on your hull.

Yes, to achieve the best possible performance and avoid potential damage to the device or your sailboat, installation by a qualified marine installer is recommended.

Required tools include:

A drillA 3 mm (1/8 in) bitA wrench suitable for nuts up to 75 mmMarine sealant (flexible, fast-curing type, for below the waterline)Mild household detergent or rubbing alcoholSandpaperMasking tapeWaterproof electrical tapeCable glands (optional)Water-based antifouling paint (optional)For a fiberglass hull: a 73 mm (2 7/8 in) hole saw and marine-grade epoxy resin (for laminated fiberglass hulls).

To avoid interference and overheating risks, do not install the depth sounder near the engine or in the engine room. It should also not be installed behind frames, beams, fittings, water intake or discharge openings, or anything that creates air bubbles or turbulent water. The depth sounder must be in clean (non-turbulent) water for optimal performance.

The choice of location is crucial for performance. Here are some guidelines:

Outboard and sterndrive boats: The depth sounder must be mounted forward and close to the engine(s).Inboard boats: The depth sounder must be mounted forward and away from the propeller and propeller shaft.Boats with a stepped hull: The depth sounder must be mounted forward of the first step.Boats with a full keel: The depth sounder must be mounted slightly angled toward the bow, parallel to the centerline.Boats with a fin keel: The depth sounder must be mounted 25 to 75 cm (10 to 30 in) forward of the keel and a maximum of 10 cm (4 in) to the side of the centerline.Displacement-hull boats: The depth sounder must be mounted approximately one-third of the waterline length from the bow, and 150 to 300 mm (6 to 12 in) to the side of the centerline.The depth sounder must be mounted parallel to the bow-stern axis of your boat.

For a fiberglass hull:

Drill a 3 mm (1/8 in) pilot hole from the outside. Place masking tape around the hole on the outside to reduce gelcoat cracking. Use a 73 mm (2 7/8 in) hole saw to cut the transducer hole through the hull from the outside. From the inside, use a slightly larger hole saw to cut only the inner fiberglass skin and core, ensuring the outer skin is not cut. Seal the exposed core inside the hull with fiberglass or casting epoxy resin to prevent water intrusion.

For a solid fiberglass hull:

Drill a 3 mm (1/8 in) pilot hole from the outside.Place masking tape around the pilot hole and the surrounding area on the outside of the hull to reduce gelcoat cracking.Use a 73 mm (2 7/8 in) hole saw to cut the depth sounder hole through the hull from the outside.Sand and clean the inside of the hole and the area around the hole.

During installation, apply marine sealant along the water path to ensure a watertight seal between the transducer and the hull. Apply a 2 mm (1/16 in) layer of marine sealant to the inner flange of the transducer housing where it contacts the hull. Also apply a layer of marine sealant along the transducer housing threads to fill the gap between the threads and the hull. The sealant on the threads should extend approximately 6 mm (1/4 in) above the inside of the hull to seal and secure the hull nut.

Yes, you must update the Garmin chartplotter software when installing this device to ensure compatibility and optimal performance.

Unless you are connecting the transducer to a black box sonar unit requiring bare-wire connections, you must not cut or splice the depth sounder cable. Cutting the depth sounder cable otherwise than what is required to connect to a black box sonar unit may void your warranty.