Garmin GT36-TM ja GT15M-IH sondipakk

This pack includes two separate transducers for versatile sonar coverage. It comprises the GT36-TM transducer, designed for transom mounting on your boat, and the GT15M-IH transducer, intended for internal hull mounting.

The GT15M-IH depth sounder delivers 600 W (RMS) transmit power. It can reach a maximum depth of 549 m (1,800 ft), depending on water conditions. Operating frequencies range from 85 to 165 kHz; the exact range depends on your chartplotter or fishfinder model. Operating temperature range is 0°C to 50°C.

The GT36-TM transducer, designed for transom mounting, is compatible with all hull materials. The GT15M-IH transducer, designed for internal mounting, is specifically recommended for solid fiberglass hulls with a maximum thickness of 16 mm (5/8 in). It is not recommended for metal, wood, or sandwich hulls (with a core).

For optimal performance, the GT36-TM transducer must be mounted on the transom, parallel to the waterline. It is recommended to install it at least 38 cm (15 in) away from the propeller and preferably on the starboard side if the propeller rotates clockwise (port side if the propeller rotates counterclockwise). The transducer must protrude approximately 3.5 mm (0.125 in) below a fiberglass hull or 10 mm (0.375 in) below an aluminum hull. Avoid areas of turbulence created by strakes, keels, or other equipment.

The GT15M-IH transducer must be installed in the bilge, near the keel and the transom, on a solid fiberglass hull surface without air gaps or core material. It must be mounted as flat as possible. The deadrise angle of the hull at the chosen location is critical for selecting the appropriate internal mounting bracket (available for deadrise angles of 0-3°, 4-8°, 9-16°, and 17-25°). Avoid areas behind through-hull fittings, protrusions, or chines that could create turbulence.

No, it is strongly discouraged to cut the depth sounder cable. Cutting the depth sounder cable voids your warranty. If the cable is too long, it is recommended to coil it carefully or use a specific Garmin cable extension (part numbers 010-11617-42 or 010-11617-32) for the GT36-TM transducer, without exceeding 9 meters (30 feet) to avoid signal degradation.

Yes, it is mandatory to update the software of your Garmin chartplotter when installing this transducer pack to ensure compatibility and optimal performance. You can find the update instructions in the user manual of your chartplotter on support.garmin.com.

Using the GT36-TM and GT15M-IH transducers together provides a hybrid and versatile sonar solution. The GT36-TM transducer (transom-mounted) delivers clear, detailed images in shallow waters and at moderate speeds, while the GT15M-IH transducer (in-hull) is ideal for fiberglass hulls, offering protection against external damage and strong performance at high speeds without creating drag. This package optimizes seabed and fish detection across various sailing conditions and hull types.

The Garmin GT36-TM and GT15M-IH transducer pack provides a hybrid sonar solution for versatile coverage. The GT36-TM transducer, designed for transom mounting, delivers ClearVü and SideVü functions, offering detailed views below and to the sides of your boat. The GT15M-IH transducer, designed for in-hull mounting, is a traditional sonar transducer that transmits signals through the hull, ideal for fiberglass hulls without drilling.

The GT36-TM transducer (transom-mounted) is compatible with all hull materials. The GT15M-IH transducer (in-hull) is specifically recommended for solid fiberglass hulls up to 16 mm (5/8 in) thick. It is not recommended for metal, wood, or sandwich hulls (with a core).

To ensure optimal performance, you must update your Garmin chartplotter’s software when installing this transducer pack. The specific frequency compatibility (85 to 165 kHz for the GT15M-IH and UHD frequencies for the GT36-TM) will depend on your chartplotter or fishfinder model.

For optimal performance, the GT36-TM transducer must be mounted parallel to the waterline and extend 3.5 mm (0.125 in) below a fiberglass hull or 10 mm (0.375 in) below an aluminum hull. It must be installed at least 38 cm (15 in) from the propeller and away from any turbulence sources such as strakes, struts, fittings, or water intakes. If the propeller rotates clockwise, mount the transducer on the starboard side; if it rotates counterclockwise, mount it on the port side.

The GT15M-IH transducer must be mounted in the bilge area, near the keel and the transom, on a solid fiberglass hull section without air gaps or core material. It should be installed as level as possible and must not be placed behind through-hull fittings or other protrusions, nor above a strake. A preliminary test phase prior to permanent installation is recommended to validate the location.

No, the GT15M-IH is an internal transducer and does not require hull penetration. It mounts inside the hull, protecting it from external damage and eliminating drag.

The deadrise angle is critical for installing the GT15M-IH. The kit includes mounting brackets suitable for different deadrise angles. You must measure the deadrise angle at the installation location and select the bracket that ensures the transducer is installed as horizontally as possible. The brackets are designed for deadrise angles of 0-3°, 4-8°, 9-16°, and 17-25°.

Yes, you can add an extension cable (Garmin part number 010-11617-42 or 010-11617-32) if the GT36-TM transducer cable is not long enough to reach the chartplotter. However, to avoid signal degradation, it is recommended not to extend the cable by more than 9 meters (30 feet).

It is imperative not to cut the probe cables. Cutting the transducer cables will void your product's warranty.

The pack includes the GT36-TM transducer with its transom mount, as well as the GT15M-IH transducer with its internal mounting kit, which comprises the tank and the necessary screws for installation.