Pöördeventilaator 12/3000 Smart

The Victron Energy Inverter 12/3000 Smart provides a continuous output power of 3000 VA (i.e., 2400 W) when operating at an ambient temperature of 25°C. It can also handle a peak power of 6000 W for starting demanding loads.

The Victron Energy Inverter 12/3000 Smart requires a DC input voltage between 9.3 V and 17 V to operate correctly. It is specifically designed for 12 V battery systems.

The inverter outputs 230 VAC with a tolerance of ±2%. The output frequency is configurable and can be set to 50 Hz or 60 Hz, depending on your specific requirements.

This inverter produces a pure sine wave output. This characteristic is essential for powering sensitive electronic equipment and household appliances, ensuring stable operation without interference.

The Inverter 12/3000 Smart inverter includes Bluetooth functionality. You can easily configure and monitor it using the VictronConnect app, available on your smartphone or tablet.

The VE.Direct communication port allows connecting the inverter to a computer via a VE.Direct to USB interface cable, or to a GX monitoring device such as the Cerbo GX. This provides full system management and monitoring.

The ECO mode allows the inverter to enter standby when the connected load drops below a predefined value (minimum 15 W). The inverter then briefly powers back on at regular intervals (default every 2.5 seconds, adjustable) to check if the load has increased. If it detects a load above the set threshold, it remains powered on.

The inverter is equipped with several protections to ensure its reliability and the safety of your installation. These include protections against:

Output short-circuitsOverloadsToo high or too low battery voltagesOverheatingAC voltage present at the outputHigh DC ripple

For optimal performance, the inverter must be installed on a flat surface. It is important to avoid any contact with water, direct exposure to sunlight, and to ensure that the ambient temperature is between -20°C and 40°C. Leave at least 10 cm of free space around the device for adequate ventilation.

The Victron Energy Inverter 12/3000 Smart can operate in an ambient temperature range from -40°C to +65°C. However, power derating applies above 40°C to maintain performance and reliability.

For optimal connection to a 12V battery, use DC cables with a 70 mm² cross-section for lengths up to 1.5 meters, and 95 mm² for lengths between 1.5 and 3 meters. The inverter’s connection terminals are M8 type.

To protect the Victron Energy Inverter 12/3000 Smart inverter in a 12V system, it is strongly recommended to install a 400A DC fuse near the battery.

The inverter is a Safety Class I product, which means the chassis must be grounded. A grounding point is located outside the product. The ground conductor must be at least half the cross-section of the conductors used for the battery connection.

Yes, the 12/3000 Smart inverter has a high starting power capacity (6000 W peak power). This allows it to start inductive loads such as power tools, LED lamp converters, or other devices requiring a high inrush current.

You can configure several inverter parameters, including:

Low battery alarm and cutoff levelsBattery voltage and output frequency (210–245 V, 50/60 Hz)ECO mode settings (enable/disable and detection level)

Yes, the inverter is equipped with a remote on/off connector. An external switch can be connected to this two-pole connector, or between the positive battery terminal and the left contact of the connector, which is useful for automotive applications, for example.

Yes, the Victron Energy Inverter 12/3000 Smart inverter is designed for marine and mobile environments. Its robustness, toroidal transformer topology, and built-in protections make it a reliable solution for providing AC power onboard.

The Victron Energy Inverter 12/3000 Smart offers a maximum efficiency of 93%. High efficiency means less energy is lost as heat and your batteries' energy is used more effectively.

Yes, thanks to its VE.Direct port, the inverter can be connected to GX monitoring devices such as the Cerbo GX. This allows full integration into a Victron energy management system, providing centralized monitoring and control.