Prekidač baterije ML-RBS s daljinskim upravljanjem 12 V

The ML-RBS 12V battery switch is designed to manage power supply for marine systems. It allows remote and manual switching of high currents under load, ensuring reliable connection or disconnection of battery banks.

The term "magnetic latching" (also called bi-stable) means that the switch only draws current for the 20 milliseconds required to change state (ON or OFF). Once the state is set, it consumes virtually no current, ensuring excellent energy efficiency.

The ML-RBS 12V has a continuous rating of 500A DC and an intermittent rating of 700A DC for 5 minutes. Its cranking rating is 1450A DC for 30 seconds when used with two 4/0 AWG cables (2x 120 mm²).

Yes, the ML-RBS is equipped with a manual control button that allows you to turn the switch on or off with or without electrical power. It also features a "LOCK OFF" function to secure the system during maintenance.

This battery switch uses silver-alloy contacts. These contacts are designed to provide high reliability when switching loads under voltage, supporting 10,000 cycles at 300A under 12V.

The battery switch is equipped with 3/8"-16 tinned copper studs. These terminals are designed for maximum conductivity and excellent corrosion resistance in marine environments.

Yes, the switch has an LED output to remotely indicate its state (ON or OFF). This function requires an optional LED or a Contura remote control switch with integrated LED, which is included in the retail packaging.

The maximum recommended tightening torque for terminal studs is 15.8 N•m (140 in-lb). It is critical to adhere to this specification to ensure a secure connection and prevent damage to the terminals.

Yes, the ML-RBS is IP66 rated, meaning it is protected against powerful water jets. It also meets external ignition protection requirements per ISO 8846 and SAE J1171, making it safe for marine environments.

The ML-RBS is rated for 100,000 mechanical switching cycles. For live switching, it supports 10,000 cycles at 12V, 300A; 10,000 cycles at 24V, 150A; and 2,000 cycles at 48V, 100A.

The Contura remote control switch included is designed to operate within a temperature range from -40°C (-40°F) to 85°C (185°F).

The ML-RBS battery switch should be installed as close as possible to the battery banks. To prevent corrosion of the wires and terminals, mount it in a dry and protected location. Avoid installing it directly above vented lead-acid batteries to prevent exposure to corrosive gases.

Terminals A and B are interchangeable. Connect the battery bank to one terminal and the load to the other. It is critical to select the appropriate wire gauge based on current to ensure system safety and performance.

Yes, the ML-RBS ships with a Contura remote control switch (model 2145). This momentary SPDT (ON)-OFF-(ON) switch allows remote control of the battery switch from a convenient location.

The ML-RBS is supplied with a Deutsch DTM connector. Note that the mating part of the connector is not included but is required for installation of the control circuit.

Before starting installation, it is imperative to disconnect all negative battery connections. All unused control wires must be carefully isolated from each other and from any accidental contact using heat-shrink tubing or insulating tape to prevent malfunctions.

To achieve the continuous 500A rating and the 1450A cranking rating, it is recommended to use two 4/0 AWG cables (2x 120 mm²). For lower currents, other wire sizes are possible, such as 2/0 AWG (70 mm²) for 225A continuous or 4/0 AWG (120 mm²) for 300A continuous.

The ML-RBS is compatible with contact voltage systems ranging from 0 to 64V DC. However, its nominal control voltage is 12V DC, requiring a control voltage of 9 to 16V DC for operation.

Yes, the ML-RBS can be used to combine or isolate battery banks. Blue Sea Systems also offers a paralleling bus (reference 9160) to simplify the coupling of multiple ML-RBS battery switches or automatic charge relays, enabling flexible power management.