Sonda ActiveImaging™ 3-u-1 s 7,6 m kabelom (25 stopa)

This is a subsurface imaging transducer designed for fishing. It integrates traditional CHIRP, SideScan, and DownScan Imaging, along with a temperature sensor, all in a single unit for simplified installation.

The Navico ActiveImaging™ 3-IN-1 transducer combines traditional CHIRP, SideScan, and DownScan Imaging technologies. It also includes a temperature sensor for measuring depth and water temperature.

Active Imaging™ technology optimizes SideScan beam steering to enhance imaging resolution and range. It enables identification of underwater structures such as rock formations, seagrass beds, and drop-offs at greater distances, providing finer details over a larger area.

This transducer operates on CHIRP mid/high frequencies (83/200 kHz) for traditional CHIRP, and specific frequencies for SideScan and DownScan Imaging to optimize imaging.

Yes, the Navico ActiveImaging™ 3-IN-1 transducer is equipped with a sensor that provides depth and water temperature data.

The weight of the ActiveImaging™ 3-IN-1 depth sounder without its cable is 0.37 kg (0.81 lbs).

The depth sounder is constructed from polymer. This material was selected because it reacts to sound waves in a manner similar to water, thereby enhancing the clarity of underwater images.

The transducer uses separate sonar elements for SideScan transmission and reception. This design increases ping speed and image resolution while improving lateral range compared to older imaging transducers.

This transducer is compatible with Lowrance multifunction displays HDS LIVE, HDS Carbon, Elite Ti2, as well as Simrad NSS evo3 series and GO series.

The Navico ActiveImaging™ 3-IN-1 transducer uses a 9-pin connector, ensuring a reliable connection with compatible devices.

The transducer is supplied with a 7.6-metre (25-foot) cable.

The ideal mounting location for the transducer is in an area where the water flow is undisturbed, to optimize the sonar signal quality.

Yes, it is not recommended to mount the transducer beyond the boat's chine, as this could disrupt water flow and affect the transducer's performance.

For installation, the recommended pilot hole diameters for screws of diameter 10 are:

For soft materials (e.g., plywood): Ø 3.7–4.0 mm (5/32"). For rigid materials (e.g., fiberglass, acrylic, hardwood): Ø 4.1–4.7 mm (3/16").

A high-quality marine-grade sealing/adhesive compound, suitable for use above or below the waterline, should be applied to the screw holes to ensure a watertight seal.

Yes, through-hull mounting (shoot-thru-hull) is an installation option for this transducer, providing protection against damage and a discreet setup.

No, through-hull transducers cannot be installed through wooden hulls. This method is typically reserved for fiberglass or composite hulls.

"3-IN-1" indicates that the transducer combines three key imaging technologies into a single unit: traditional CHIRP, SideScan, and DownScan Imaging. This provides a complete and detailed view of the underwater environment.

The Navico ActiveImaging™ 3-IN-1 Active Imaging™ transducer is designed to be compatible with several multifunction display ranges, ensuring seamless integration with your navigation system. It is compatible with:

Lowrance HDS LIVE multifunction displaysLowrance HDS Carbon multifunction displaysLowrance Elite Ti2 multifunction displaysSimrad NSS evo3 seriesSimrad GO series

To ensure optimal performance of your ActiveImaging™ 3-IN-1 transducer, it is essential to follow these mounting recommendations:

Ideal location: The transducer must be installed in an area with undisturbed water flow.Location to avoid: It is strongly discouraged to mount the transducer beyond the chine line of your boat.Mounting options: The transducer can be installed in different ways, including on the transom, on an electric motor forward, or via through-hull mounting.Guide holes recommended for screws with a 10 mm diameter:For soft materials (e.g., plywood): use a 3.7–4.0 mm (5/32") drill bit.For rigid materials (e.g., fiberglass, acrylic, hardwood): use a 4.1–4.7 mm (3/16") drill bit.Sealing: Apply a high-quality marine-grade sealant/adhesive, suitable for use above or below the waterline, to all guide holes to ensure watertightness.Important note for through-hull mounting: Transducers with through-hull mounting cannot be used with wooden hulls.