Skylla IP65 12/70(3)

This Victron Energy Skylla IP65 charger is designed for 12V systems and delivers a total charge current of 70A.

The Skylla IP65 12/70(3) charger has three charge outputs, allowing simultaneous power supply to multiple battery banks.

The IP65 protection rating means the charger is dust-tight and protected against water jets. This makes it particularly suitable for installations in marine environments or other locations potentially exposed to moisture.

The Skylla IP65 charger can operate over a wide universal input voltage range, from 90 to 265 V AC (50/60 Hz) and from 90 to 400 V DC. This allows flexible use with various power sources.

Yes, this Skylla IP65 charger integrates the functionality to be used as a direct power supply, providing additional flexibility.

Yes, the Skylla IP65 charger is equipped with microprocessor control for optimized battery charging.

This charger integrates several advanced features for optimal charging:

An external temperature sensor for temperature-compensated charging. Detection of battery voltage to compensate for voltage losses due to cable resistance.

It is recommended to keep the cable length between the charger and the battery under 6 meters to ensure efficient charging.

The charger's grounding point must be connected to a proper ground according to applicable safety standards. On a vessel, connect it to the ground plate or hull. On land, connect it to the electrical grid ground. For mobile applications (vehicle, car, or caravan), connect it to the vehicle's chassis.

No, the Skylla charger is NOT protected against battery polarity reversal. It is critical to follow the installation procedure to avoid damaging the device, as the warranty does not cover defects caused by polarity reversal.

For external voltage detection, a red wire (0.75 mm²) must be connected between the positive terminal of the battery and the "+ Voltage sensor" connector. A black wire (0.75 mm²) must be connected between the negative terminal of the battery and the "- Voltage sensor" connector.

The remote on/off input can be connected to a switch or an open-collector optocoupler. It is recommended to use twisted wires for this sensitive connection. If no remote switch is connected, the remote on/off terminals must be short-circuited with a short wire.

Yes, the on/off remote input of the charger can be connected to a lithium battery management system (BMS) VE.Bus, such as the 'charge disconnect' output of a VE.Bus BMS, via a specific cable.

Yes, the VE.Can ports (RJ45) provide access for monitoring and control. The charger can be connected to a Skylla-i Control GX panel, a GX device such as the Cerbo GX, or to an NMEA 2000 network using a VE.Can to NMEA 2000 accessory cable.

Yes, multiple chargers can be synchronized for parallel operation via the CAN interface. This is done by simply interconnecting the chargers with RJ45 UTP cables, ensuring that bus terminators are used at the ends of the network.

The IP65 protection rating means the Victron Energy Skylla IP65 12/70(3) charger is fully protected against dust (first digit '6') and water jets from all directions (second digit '5').

This protection makes it particularly suitable for installations in marine environments or other locations potentially exposed to moisture, splashes, and dust, ensuring its durability and reliability.

For correct and safe installation of your Skylla IP65 12/70(3) charger, here are the essential points to follow:

Location: Install the charger in a dry and well-ventilated area. Wall or floor mounting is possible, but vertical mounting improves air circulation and extends the device's lifespan.Cable length: Keep the cable length between the charger and the battery under 6 meters to minimize voltage losses.Grounding: Connect the charger's grounding point to a proper earth ground. On a boat, connect it to the ground plate or hull. On land, connect it to the electrical network ground. For mobile applications, connect it to the vehicle chassis.Battery polarity: The Skylla is NOT protected against reversed battery polarity. Strictly follow the installation procedure to connect the positive and negative cables to the correct terminals to avoid damaging the device.Power supply: The on/off switch on the front of the unit does not cut the mains power. Always disconnect the mains power before making or breaking battery connections.Cable cross-section: Use cables with the appropriate cross-section for battery connections to ensure efficient and safe charging. Refer to the user manual for specific cable cross-section recommendations for your installation.

Yes, the Skylla IP65 12/70(3) charger offers high flexibility in terms of compatibility:

Power sources: It accepts a wide universal input voltage range from 90 to 265 V AC (50/60 Hz) and from 90 to 400 V DC, making it usable in different regions or with various power sources.External sensors: It is compatible with external voltage and temperature sensors, enabling more precise charging adjusted to the battery’s actual conditions.Remote control: A remote on/off input port is available for external control.Monitoring and management systems: Thanks to its CAN-bus interface (VE.Can), the charger can be integrated with Victron Energy energy management systems such as the Skylla-i Control GX panel or a GX device like the Cerbo GX. It can also be connected to an NMEA 2000 network via a specific accessory cable.Lithium battery management systems (BMS): The charger is compatible with VE.Bus BMS lithium battery management systems via the VE.Can connection, allowing automatic communication of charge authorization conditions.

The Victron Energy Skylla IP65 12/70(3) charger has three separate outputs. This means it can charge up to three independent battery banks simultaneously, such as a main service battery bank, a starter battery, and an auxiliary battery.

It is important to note that, depending on the Skylla range design, the starter battery can draw current from the main battery if its voltage is lower. However, the main battery cannot draw current from the starter battery, even if the latter is fully charged and the main battery is at a low charge level.

The Victron Energy Skylla IP65 12/70(3) battery charger is a marine battery charger designed for 12V systems. Here are its main features:

Output voltage: It is designed for 12V battery systems.Charge current: It delivers a total charge current of 70 amperes.Number of outputs: It has three separate outputs, allowing simultaneous charging of multiple battery banks (for example, the main battery, the starter battery, and an auxiliary battery).Protection rating: Its IP65 rating indicates complete resistance to dust and water jets. This makes it particularly suitable for installations in marine environments potentially exposed to moisture.Input voltage range: It can operate on a universal input voltage range of 90 to 265 V AC (50/60 Hz) and 90 to 400 V DC, offering great flexibility of use.Thanks to its IP65 protection rating and robust design, this charger is fully suited for marine use.