BMS NG

The VE.Bus BMS NG is a battery management system (BMS) designed specifically for Victron Energy Lithium NG lithium iron phosphate (LiFePO4) batteries. Its primary function is to protect and control these batteries within systems that include a Victron VE.Bus inverter/charger or inverter.

The VE.Bus BMS NG is compatible exclusively with Victron Energy Lithium NG batteries. It is not designed for use with Victron Lithium Smart batteries (without the NG designation).

The BMS NG provides several essential protection functions:

It generates a pre-alarm in case of imminent cell undervoltage. It disables the inverter function of VE.Bus chargers/converters and disconnects loads via its dedicated output in case of cell undervoltage. It disables charging from VE.Bus chargers/converters, VE.Direct and VE.Can solar chargers (via a GX device), and disconnects other chargers in case of cell overvoltage, cell undertemperature or cell overheating.

The VE.Bus BMS NG uses several communication interfaces:

VE.Bus: Two RJ45 ports allow connection to VE.Bus products such as MultiPlus, Quattro, or inverters.Bluetooth Smart: For configuration, monitoring, and firmware updates via the VictronConnect app on smartphone or tablet.'Remote panel' port: To connect GX devices (such as a Cerbo GX), Digital Multi Control (DMC) panels, or VE.Bus Smart dongles.

The VE.Bus BMS NG can be used to create battery banks suitable for system voltages of 12V, 24V or 48V, by combining 12.8V, 25.6V and 51.2V Lithium NG batteries in series, parallel or a combination of both.

The VE.Bus BMS NG allows connection of:

Up to 50 batteries for 12 V or 24 V system configurations.Up to 25 batteries for 48 V system configurations.This enables a maximum storage capacity of 192 kWh for 12 V systems, 384 kWh for 24 V systems, and 128 kWh for 48 V systems.

Yes, the VE.Bus BMS NG includes Bluetooth Smart. This feature enables configuration, monitoring, and software updates wirelessly via the VictronConnect app. It also provides instant readings of key data such as state of charge (SoC), battery temperature, warnings, and alarms directly in the device list.

The DC power cable for the BMS is not included. You must use a single-core cable with a cross-section of at least 0.75 mm² (AWG 16) and include an inline 1A fuse.

The VE.Bus BMS NG must be installed exclusively by qualified and trained installers, strictly following national safety regulations.

The VE.Bus BMS NG pre-alarm output is designed to trigger a visible or audible warning when battery voltage is low. It activates at least 30 seconds before the load-disconnect output is disabled due to cell undervoltage. It can drive a relay, LED, or buzzer, with a maximum output current of 1A.

The VE.Bus BMS NG has two main control outputs:

Load Disconnect output: Controls the remote on/off input of a BatteryProtect, inverters, DC-DC converters, or other loads with this feature. It is normally high and goes floating in case of imminent cell undervoltage.

Charge Disconnect output: Controls the remote on/off input of chargers such as the Smart Charger IP43, a Cyrix-Li-Charge relay, a Cyrix-Li-ct, or a BatteryProtect. It is normally high and goes floating in case of imminent cell overvoltage or overheating.

The Remote L and Remote H remote on/off terminal allows remote control of load disconnect and charger outputs. When this terminal is disabled, both outputs become floating, thereby shutting off connected loads and chargers. It can be actuated by a switch or relay contact between L and H, or by connecting H to the battery positive or L to the battery negative.

Yes, the VE.Bus BMS NG can disable charging from VE.Direct and VE.Can solar chargers via a GX device in case of cell overvoltage, low temperature, or overheating.

The VE.Bus BMS NG is equipped with three LED indicators:

A blue LED for Bluetooth status. A red LED for warnings and alarm errors. A VE.Bus status LED.

The VE.Bus BMS NG operates with an input voltage range of 9 to 70 VDC.

The current consumption of the VE.Bus BMS NG varies depending on its state:

In normal operation: 10 mA (excluding load disconnection current).At low cell voltage: 2 mA.When turned off via the remote on/off terminal: 1.50 mA.

The VE.Bus BMS NG has a dedicated power output (GX-Power) capable of supplying up to 1A to a GX device. This output powers the GX device from the battery or the auxiliary input (Aux-In), depending on the highest available voltage.

The VE.Bus BMS NG has the following dimensions: 23.2 mm (height) x 95.0 mm (width) x 105.8 mm (depth). Its weight is 120 grams.

The VE.Bus BMS NG has an IP20 protection rating, meaning it is protected against solid objects larger than 12.5 mm but offers no water resistance.

The VE.Bus BMS NG is specifically designed to be compatible with Victron Energy Lithium NG batteries. It must not be confused with Lithium Smart batteries (without the NG designation), with which it is not compatible.

These Lithium NG batteries are based on Lithium Iron Phosphate (LiFePO₄) technology and are available in different voltages:

12.8 V25.6 V51.2 VThey can be connected in series, parallel, or a combination of both, to create battery banks suitable for 12 V, 24 V, or 48 V systems. The BMS NG monitors and protects each individual cell of these batteries.