Komplektas ST4000 galios bloko atnaujinimui į MKII versiją

The Raymarine E12093 update kit is designed to modernize existing ST4000 autopilot systems. It replaces the old power unit with a Mk II wheel drive, integrating the technology from Raymarine's Evolution autopilot range. This kit aims to enhance the performance of the helm control unit and extend the lifespan of ST4000 systems.

The drive unit supplied in this kit is compatible with 3-, 4-, 5-, 6-, 7-, or 8-spoke wheels.

The drive unit has a front cover diameter of 228 mm (9.0 in) and an overall diameter of 361 mm (14.2 in). Its height is 135 mm (5.3 in). The motor tube has a diameter of 48 mm (1.9 in) and a length of 171 mm (6.7 in), requiring an additional 60 mm (2.4 in) clearance for the cable.

No, this kit is a targeted upgrade. It replaces the power unit with a Mk II wheel drive and integrates with the existing ST4000 autopilot controller, but does not constitute a complete system replacement.

The E12093 kit includes the following items:

The wheel drive unitA pedestal mountThree 16 mm spoke clamping insertsThree 12 mm spoke clamping insertsSix spoke clampsSix M5 x 16 mm clamping screwsFour #10 x ¾ in mounting screwsA 6 mm drill bitA 4 mm drill bitA 3 mm Allen keyTwo ball jointsOne tiller pinThree #8 x ¾ in socket head screwsOne studTwo nutsTwo #8 x ¾ in countersunk screwsA 4.5 m (15 ft) power cableOne cable clip and a #6 x ½ in screw

Installing the drive wheel unit involves four main steps:

Drilling the clamping holes for the spokes in the front cover.Attaching the drive wheel unit to the wheel.Attaching the pedestal bracket.Connecting the drive to the existing control unit.

The unit is designed to operate with steering systems having between 1 and 3.5 turns lock-to-lock.

Yes, the cover must be removed from the drive unit. The cover is held in place by three "push-fit" posts that insert into three sockets on the drive ring. To remove it, hold the motor with one hand and pull the cover upward and away from the drive unit.

The spoke holes are numbered inside the cover. Position the cover arrow upwards and refer to the diagrams in the manual to identify the correct holes based on your wheel’s spoke count (e.g., for a 5-spoke wheel, drill the 4 holes marked '5'). Mark the holes and check alignment by placing the cover against your wheel.

Raymarine's EMC installation guidelines recommend using the cables specified by Raymarine. Cutting and reconnecting these cables can compromise EMC performance and should be avoided unless detailed in the installation manual.

Yes, it is crucial to ensure the electrical power supply is disconnected before making any electrical connections for safety reasons.

Yes, although the product is supplied with default settings, it is necessary to complete the commissioning procedures detailed in the "Commissioning" section of the relevant autopilot controller manual to ensure optimal performance on your sailboat.

To register your new Raymarine product, you can do so on the Raymarine website at www.raymarine.com/warranty.

For optimal EMC performance, Raymarine equipment and connected cables should be:

At least 1 meter (3 feet) away from any equipment transmitting or cables carrying radio signals (e.g., VHF radios, cables, and antennas). For SSB radios, this distance must be increased to 2 meters (7 feet).More than 2 meters (7 feet) away from the path of a radar beam.Equipment should be powered by a battery separate from the one used for engine starting, to avoid voltage drops and starter transients that could cause equipment to reset.

This kit integrates Raymarine Evolution autopilot technology into an existing ST4000 system by replacing the power unit with a Mk II wheel drive.

The kit is specifically designed as an "ST4000 power unit upgrade kit to MKII" and integrates with the existing ST4000 autopilot controller. It is not stated to be compatible with other controllers.

The kit includes a power cable with a length of 4.5 meters (15 feet).

Yes, the kit includes a 6 mm drill bit and a 4 mm drill bit, as well as a 3 mm Allen key, required for certain installation steps.

The pedestal mount is a component included in the kit, essential for securing the drive unit to your boat's helm pedestal, ensuring a stable and secure installation.