Lynx Smart BMS 1000 NG (M10)

The Lynx Smart BMS 1000 NG (M10) is a battery management system (BMS) designed for Victron Lithium NG batteries. It is built for systems requiring high current capacity, integrating a 1000 A continuous contactor. This is the most feature-rich and complete option in the range for these batteries.

The Lynx Smart BMS 1000 NG is specifically designed for Victron Lithium NG batteries. These batteries use Lithium Iron Phosphate (LiFePO₄) technology and are available in 12.8 V, 25.6 V, and 51.2 V variants with various capacities.

The Lynx Smart BMS 1000 NG integrates a main safety contactor with a DC current rating of 1000 A. It can also handle a peak current of 1200 A for 5 minutes.

The Lynx Smart BMS 1000 NG acts as an essential secondary safety system, protecting batteries in case of primary control failures (ATC, ATD and/or DVCC). It protects against deep discharge and battery overcharging.

Yes, a pre-charge circuit is integrated into the Lynx Smart BMS 1000 NG. It prevents high inrush currents when connecting capacitive loads, such as inverters, eliminating the need for external pre-charge devices.

Monitoring is handled through several methods:

Via Bluetooth connectivity and the VictronConnect app.Via VE.Can connectivity combined with GX devices (such as the Cerbo GX or Ekrano GX).Via the VRM portal.These interfaces provide real-time readings of cell voltages and temperatures, as well as comprehensive data from the integrated battery monitor (state of charge, voltage, current, historical data, etc.).

The Lynx Smart BMS 1000 NG functions can be controlled via:

The VictronConnect app via Bluetooth. GX devices (such as the Cerbo GX or Ekrano GX) via VE.Can. Closed-loop DVCC control that automatically manages compatible chargers/inverters via a connected GX device. The ATC/ATD contacts, which can be used to control other chargers and loads with a remote on/off port.

The Lynx Smart BMS 1000 NG integrates seamlessly into Victron Energy's Lynx Distributor M10 system. It shares M10 busbars for simplified and organized connections with other Lynx M10 products. It also communicates with GX devices via VE.Can and is compatible with the VRM portal for remote monitoring.

The Lynx Smart BMS 1000 NG supports battery system voltages of 12 V, 24 V or 48 V.

A single Lynx Smart BMS 1000 NG can manage up to 50 batteries if they are configured for 12 V or 24 V systems. For 48 V systems, it can manage up to 25 batteries.

The maximum energy storage capacity supported by a single Lynx Smart BMS 1000 NG depends on the system voltage:

Up to 192 kWh with 12 V batteries.Up to 384 kWh with 24 V batteries.Up to 128 kWh with 48 V batteries.

Yes, it is possible to connect multiple Lynx Smart BMS units in parallel. This feature allows you to increase energy storage capacity and provide system redundancy. Up to 5 BMS units can be connected in parallel in the same installation.

Yes, the Lynx Smart BMS 1000 NG can be integrated into marine networks via the NMEA 2000 protocol. This requires the use of a VE.Can to NMEA 2000 micro-C male cable for the connection.

The programmable relay can be used in two main ways:

As an alarm relay (combined with the pre-alarm).To control an alternator via its external regulator (ignition wire), with an Alternator ATC mode for safe alternator disconnection before battery disconnection.

The AUX port provides an embedded auxiliary power supply (1.1 A at system voltage) to power specific loads, such as a GX device, after the BMS shuts down. The BMS and the AUX connection automatically power off if no charging voltage is detected within 5 minutes following a low-voltage event.

Yes, the Lynx Smart BMS 1000 NG can monitor the fuse status of up to 4 connected Lynx Distributors. This monitoring is accessible via the VictronConnect app or GX devices, and alarms are triggered in case of blown fuses.

The Lynx Smart BMS 1000 NG uses M10 busbar connections. These busbars (8 x 30 mm tinned copper) are designed to be combined with all Lynx M10 products, enabling modular and robust integration.

The dimensions of the Lynx Smart BMS 1000 NG housing are 230 mm (height) x 180 mm (width) x 100 mm (depth). The unit weighs 2.7 kg.

The Lynx Smart BMS 1000 NG is designed to operate within a temperature range from -40 °C to +60 °C.

The electrical consumption of the Lynx Smart BMS 1000 NG varies depending on its operating mode:

In OFF mode: 0.3 mA. In standby mode (Standby): Approximately 0.6 W (50 mA at 12 V). In ON mode: Approximately 4.2 W (350 mA at 12 V), which may vary depending on the state of the relays.