Kamera montażowa na pokład GC™ 245, czarna

The Garmin GC™ 245 marine camera is a versatile monitoring solution designed to integrate with Garmin BlueNet™ and Garmin Marine Network navigation systems. It features an adjustable lens module for a wide viewing angle:

Horizontal rotation of 80 degreesVertical tilt of 62 degreesRoll of 90 degreesThis camera is ideal for various applications, such as deck monitoring, engine room surveillance, or as a stern maneuvering aid. It comes with a GVAM 10 black housing that simplifies connection to the onboard network, including a 2-meter Garmin BlueNet™ cable and a 2-meter power cable.

The GC™ 245 camera is designed for advanced integration with Garmin systems. Here are the connectivity options:

For Garmin BlueNet™ systems: The GVAM 10 black housing includes a 2-metre Garmin BlueNet™ cable that can be connected directly to a compatible BlueNet GPSMAP® chartplotter or a Garmin BlueNet 20 switch.For existing Garmin Marine Network systems: A separate Garmin Marine Network adapter cable (part number 010-12531-01), sold separately, is required to connect the GVAM 10 housing to your existing Garmin Marine Network.If your boat is equipped with a Garmin BlueNet 30 bridge, it is recommended to connect the GVAM 10 housing to the BlueNet side of the network for optimal performance and support of future updates.

Yes, the GC™ 245 camera lens module is fully adjustable to allow you to fine-tune the orientation after installation. It offers:

A rotation of the camera housing on its base plate up to 80 degrees. A downward tilt of the lens module up to 62 degrees. A roll (rotation) of the lens module up to 90 degrees. Once the desired field of view is confirmed on your chartplotter screen, you must lock the camera in position by tightening the locking ring using the supplied Allen key. It is recommended to install the camera with the lens pointing down at approximately 35 degrees relative to the waterline for an adequate view of objects close to your vessel.

For a correct installation of the Garmin GC™ 245 camera, you will need the following tools:

2.8 mm (7/64 in) and 4.5 mm (3/16 in) drill bits suitable for the mounting surface. A 9.5 mm (3/8 in) drill bit if you choose to route the camera cable inside the mounting surface. An 8 mm (5/16 in) SMA torque wrench capable of tightening to 9 kgf-cm (8 lbf-in) for SMA connectors. An 8 mm (5/16 in) wrench to hold an SMA connector while tightening the other. A #2 Phillips screwdriver or bit. 3M™ Marine Adhesive Sealant 5200 or equivalent marine adhesive sealant.

The choice of mounting location is crucial for performance and durability:

For the GC™ 245 camera: It must be mounted above the waterline.For the GVAM 10 black housing: It must be mounted in a location that will not be submerged.Ensure adequate ventilation to prevent heat buildup.The housing and its integrated network cable must be installed at least 71 cm (28 in) from noisy electrical sources, such as ignition wires and other sensitive electronic devices.Allow sufficient space for cable routing and connections.

It is mandatory to use the cables and connectors provided by Garmin when installing the system. Using cables or connectors other than those supplied by Garmin will void the product warranty. The system includes:

An 8-meter (26.25 feet) coaxial cable for the camera. A 2-meter (6.56 feet) Garmin BlueNet™ cable integrated into the GVAM 10 housing. A 2-meter (6.56 feet) power cable integrated into the GVAM 10 housing. It is strongly discouraged to cut, terminate, or splice the supplied coaxial cable, as this could cause system malfunctions. Failures caused by extended or modified coaxial cables are not covered by the warranty. Longer coaxial cables (25 m, part number 010-13026-02) are available for purchase if needed.

The GC™ 245 camera is compatible with Garmin GPSMAP® chartplotters that support Garmin BlueNet™ or Garmin Marine Network systems. For optimal compatibility and best performance, it is recommended to connect the camera via the Garmin BlueNet™ network if your GPSMAP® chartplotter allows it. If you are using an older GPSMAP® chartplotter on a Garmin Marine Network, an adapter cable (part number 010-12531-01, sold separately) will be required to establish the connection.

The GVAM 10 black housing is a key component of the GC™ 245 marine camera system. It has several core functions:

Simplifies network connection: It includes a 2 m Garmin BlueNet™ cable to easily connect the camera to your boat’s navigation network, whether it’s a BlueNet™ system or, with an adapter, a Garmin Marine Network.Power management: It features a 2 m power cable to supply the camera.Central interface: It serves as an interface between the camera and the GPSMAP® chartplotter, ensuring stable transmission of video data.The GVAM 10 housing is designed to simplify installation and integration of the camera into your marine electronics system.

The Garmin GC™ 245 marine camera is a versatile monitoring solution designed to integrate with Garmin BlueNet™ and Garmin Marine Network navigation systems. Equipped with an adjustable lens module, it is ideal for various applications such as deck monitoring, engine room surveillance, or as a stern maneuvering aid.

The lens module of the GC™ 245 camera is adjustable, allowing precise adaptation of the viewing angle. It offers 80 degrees of horizontal rotation, 62 degrees of vertical tilt downward, and 90 degrees of roll (clockwise or counterclockwise). A red dot marks the top of the lens.

The GVAM 10 black box is an essential component that facilitates the connection of the GC™ 245 camera to the onboard network. This box integrates a 2-metre Garmin BlueNet™ cable and a 2-metre power cable, simplifying system installation.

The GC™ 245 camera is designed for flush deck mounting and must be installed above the waterline. It is recommended to install it in a location not exposed to extreme temperatures or conditions. For an adequate view of objects close to your boat, install the camera with the lens pointing down at approximately 35 degrees relative to the waterline.

The GVAM 10 black housing must be mounted in a location where it will not be submerged and where it has adequate ventilation to prevent heat buildup. It is also necessary to mount it and route its network cable at least 71 cm (28 inches) away from noisy electrical sources, such as ignition wires and other sensitive electronic devices.

For installing the GC™ 245 camera, the following tools are required:

A 2.8 mm (7/64 in) drill bit suitable for the camera’s mounting surface. A 4.5 mm (3/16 in) drill bit suitable for the black housing’s mounting surface. A 9.5 mm (3/8 in) drill bit to drill the camera’s mounting surface for internal cable routing (optional). A torque wrench for SMA connector at 8 mm (5/16 in), capable of tightening to 9 kgf-cm (8 lbf-in). An 8 mm (5/16 in) wrench to hold the SMA connector. A Phillips screwdriver #2 or bit. Marine-grade adhesive sealant 3M™ Marine Adhesive Sealant 5200 or equivalent.

The coaxial cable for the GC™ 245 camera can be routed in two ways: either through the hull by drilling a 10 mm (3/8 in) cable gland hole, or externally along the mounting surface. It is critical not to cut, splice, or join the supplied coaxial cable, as this may cause system malfunction.

It is not recommended to print a mounting template yourself. It is preferable to use the template provided in the product box. If you must print one, it is crucial to ensure that the print scale is set to 100% and that the paper is large enough to avoid incorrect cutting on your boat's mounting surface.

The GVAM 10 black housing includes a Garmin BlueNet™ cable of 2 metres (6.56 feet) and a power cable of 2 metres (6.56 feet). The GC™ 245 camera comes with an 8-metre (26.25 feet) coaxial cable.

The GC™ 245 camera is compatible with Garmin GPSMAP® chartplotters and can integrate with Garmin BlueNet™ and Garmin Marine Network systems. It is designed to work with Garmin BlueNet devices and Garmin Marine Network devices.

To connect the GC™ 245 camera to an existing Garmin Marine Network system, you must use a Garmin Marine Network adapter cable (part number 010-12531-01), which is sold separately. This cable links the Garmin BlueNet™ integrated cable of the GVAM 10 housing to your Garmin Marine Network chartplotter or a GMS™ 10 port expander.

Yes, it is possible to extend the length of certain cables if necessary:

If the black GVAM 10 box is more than 2 metres from your Garmin chartplotter or BlueNet switch, you can extend the integrated Garmin BlueNet™ network cable by purchasing an additional Garmin BlueNet™ cable and a coupler. If the black box is more than 2 metres from your power supply, you can extend the power cable. If the camera is more than 8 metres from its black box, you can use a longer coaxial cable, such as the 25-metre cable (reference 010-13026-02), available from your Garmin dealer or at garmin.com. It is important not to modify the supplied coaxial cables, as this could void the warranty.