LUX DL50, plafonnier 5 W, oprawa białe

The Garmin LUX DL50 downlight is a 5-watt marine recessed luminaire designed for interior and exterior lighting on vessels. It provides CRGBW (cool white, red, green, blue, warm white) full-spectrum lighting with adjustable white color temperature ranging from 2700K (warm white) to 6500K (cool white). Its ultra-thin 2 mm front protrusion profile allows for discreet integration on flat surfaces.

The LUX DL50 downlight provides full-spectrum CRGBW lighting, meaning it can produce cool white, red, green, blue, and warm white. The white color temperature is also adjustable, ranging from 2700K (warm white) to 6500K (cool white).

Yes, the LUX DL50 downlight is designed for installation both indoors and outdoors. It is rated IP68, ensuring full dust-tightness and protection against temporary immersion. It can be installed in wet areas but is not designed for permanent submersion.

The Garmin LUX DL50 downlight has a nominal power of 5 watts. The actual power consumed is approximately 4.5 watts per light.

The LUX DL50 downlight operates on a DC voltage range of 10.5 to 31 volts.

The typical electrical consumption of the LUX DL50 downlight is 0.37 amperes at 12 volts and 0.18 amperes at 24 volts.

The LUX DL50 downlight allows adjustment of the white color temperature from 2700K (warm white) to 6500K (cool white), providing flexibility for different lighting ambiances.

The LUX DL50 downlight housing is made from hard-anodized aluminum, providing durability and corrosion resistance suitable for marine environments. It also features a white trim ring.

Yes, the rear of the light fixture can become hot to the touch during operation. However, this will not damage the mounting surface.

To install the LUX DL50 downlight, you will need to cut a hole with a diameter of 50.80 mm (2 inches). The required mounting depth is 28.30 mm (1.11 inches). The front diameter of the luminaire is 64 mm.

For indoor installations, use the supplied spring clips. After cutting the 50.80 mm hole, gently pull the spring clips backward and insert the luminaire into the hole, releasing the clips once the downlight is in place. Ensure the surface is flat.

For outdoor installations or in damp areas, it is recommended to secure the light fixture using marine-grade sealant or adhesive. Remove the spring clips from the fixture, apply a small amount of adhesive around the glass collar, and press the fixture into place while rotating slightly to spread the adhesive evenly. Clean off any excess adhesive with a soft cloth and soapy water (do not use chemical cleaners).

No, the LUX DL50 downlight must be mounted on a flat surface to ensure correct installation and optimal waterproofing.

Before any installation, always ensure the vessel's power source and battery are disconnected or isolated to prevent any electrical risk.

A qualified professional should install the LUX DL50 downlight to ensure safety and compliance with standards.

The LUX DL50 downlight is designed to operate exclusively with the Lumishore LUX Downlight control module. This module manages the luminaire's dimming and color functions.

No, it is essential not to connect the LUX DL50 downlight to third-party lighting control products or dimmers. It must be used only with the Lumishore LUX Downlight control module, otherwise the warranty will be void.

No, the Lumishore LUX Downlight control module is specifically designed to work only with Lumishore LUX lighting strip products. Using it with lighting strips from other brands will void the warranty.

Lumishore lighting systems, including the LUX DL50 downlight, are warranted against manufacturing defects for a period of three years from the original purchase date.

The warranty may be voided in cases of misuse, abuse, incorrect installation, negligence, damage caused by disasters (fire, flood, lightning), installation by unqualified personnel, unauthorized repair or modification, or failure to comply with the installation, maintenance, and usage instructions provided in the document.