Sonda TA plastikowa 500W (77/200kHz) + temperatura (4 piny)

This transducer is designed for installation on the transom (TA) of your boat. It is mounted outside the hull, at the stern of the vessel, using a bracket and screws.

For traditional sonar, this transducer operates on frequencies of 77/200 kHz. For ClearVü/DownVü scanning, it uses CHIRP technology on frequencies of 455 kHz (435-475 kHz) and 800 kHz (800-840 kHz).

This transducer has a transmission power of 500 W for traditional sonar and ClearVü.

Yes, this transducer is equipped with an integrated fast-response temperature sensor.

In traditional sonar mode, this transducer can reach maximum depths of 579 meters (1,900 feet).

For ClearVü/DownVü scanning, this transducer can provide clear images of structure and fish down to a depth of 229 meters (750 feet).

ClearVü beam widths are 2.5°x53° at 455 kHz and 1.6°x29° at 800 kHz.

This transducer is made of plastic, making it compatible with all hull materials.

The beam angle is crucial because the depth sounder sends a sonar signal that must bounce off objects and return. If the transducer is not parallel to the water surface, the signal may bounce away from the transducer, preventing the chartplotter from providing clear and accurate images. Precise beam angle adjustment strengthens the signal.

This depth sounder is compatible with many Garmin chartplotters via its 4-pin connector.

Yes, this transom-mounted transducer is suitable for towed boats. It is also compatible with all hull materials.

No, this transducer is not recommended for use with sailboats due to excessive heel, nor for vessels with stepped hulls.

For installation, you will need the following tools:

A drill and drill bits (notably 4 mm / 5/32 in and 3.2 mm / 1/8 in)
A 9.5 mm (3/8 in) wrench
Masking tape
A No. 2 Phillips screwdriver
Marine sealant

You must mount the transducer as close as possible to the center of the boat, ensuring it is away from turbulence zones created by propellers, strakes, fittings, water intakes, or outlets. For single-engine hulls, do not mount it in the propeller’s path. For twin-engine hulls, mount it between the two engines if possible. It must be at least 38 cm (15 in) from the propeller and on the opposite side of the propeller’s rotation direction to avoid propeller wash.

Position the bracket so that the center of the bottom of the transducer is level with the lower edge of the transom and parallel to the waterline. Mark the positions of the two outer holes. Wrap tape around a 4 mm (5/32 in) drill bit 25 mm (1 in) from the tip to prevent drilling too deep. On fiberglass, place tape over the hole locations to reduce gelcoat cracking. Then drill the pilot holes to a depth of about 25 mm (1 in).

Yes, it is essential to apply marine sealant to the 30 mm mounting screws before securing the entire depth sounder to the transom. If you route the cable through the transom, you must also completely fill the cable pass-through hole with marine sealant to prevent water ingress into the boat.

Route the transducer cable to the chartplotter, avoiding proximity to electrical wires or other sources of electrical interference. Create a service loop at least 25 cm (10 in) long in the cable. Secure the cable above and below the motor's swivel joint using black electrical tape or cable ties, without overtightening to avoid damaging the cable.

After installation, launch the boat and check for leaks around the screw holes below the waterline. Power on the chartplotter and drive the boat at low speed, then gradually increase speed while monitoring the sonar signal. If the signal degrades or is lost, note the speed, make moderate turns, and adjust the depth sounder depth in small increments (about 3 mm / 1/8 in) if necessary. If the issue persists, consider relocating the transducer.

Yes, cutting the depth sounder cable will void your warranty.