Ładowarka EasyCharge 10 A

The Mastervolt EasyCharge 10A (reference 43321000) is a robust and high-performance battery charger designed specifically for marine environments. It is intended for permanent connection to the AC and DC electrical systems of your boat installation. This model provides a charging capacity of 10 A for 12 V systems and 5 A for 24 V systems, and includes two independent charging outputs.

The Mastervolt EasyCharge 10A charger is designed to withstand demanding marine conditions. It features an IP68 protection rating, making it fully dust-tight and submersible. Its robust housing allows it to operate in an ambient temperature range from –20°C to 50°C.

The Mastervolt EasyCharge 10A charger is equipped with multiple protections to ensure the safety of your installation and batteries. It protects against:

SparkingShort circuitsReverse polarityOvervoltageCurrent limitingExcessive temperature

The EasyCharge 10A charger uses a 5-stage smart charging cycle to optimize battery lifespan:

Desulfation: The charger checks connections and applies a low current in case of deep discharge to bring the battery back to a normal voltage level.Bulk: The charger delivers its maximum current to rapidly charge the battery (0 to 75%).Absorption: The maximum charging voltage is reached and the current gradually decreases until the battery is fully charged at 100%.Float: The battery is fully charged and the charger stabilizes the voltage at 13.3 V before shutting off.Equalization: The charger monitors the battery and restarts a full cycle if the voltage drops below 12 V or after 14 days without charging.

The Sense-Send technology allows the Mastervolt EasyCharge 10A charger, which has two charge outputs, to dynamically analyze the needs of each connected battery. It distributes power optimally, allocating more current to the battery with the greatest need. This ensures reduced charging times, especially when batteries have different discharge levels.

The Mastervolt EasyCharge 10A charger is designed to operate within an ambient temperature range of –20°C to 50°C. Power may be reduced from 40°C to limit internal temperature and protect the device.

The Mastervolt EasyCharge 10A charger can charge batteries with a nominal voltage of 12V or 24V.

No, it is imperative never to attempt to recharge non-rechargeable batteries. Furthermore, for safety reasons and to avoid any damage, you must never charge a frozen battery or a damaged battery.

For optimal and safe installation, the charger must be mounted on a solid vertical surface that is heat-resistant, with the connectors facing downward. It is crucial to ensure that the hot air generated during operation can dissipate by leaving a clearance of at least 20 cm without obstructions around the charger. Additionally, place the charger as far from the battery as the DC cables allow and avoid installing it directly above batteries to prevent damage from corrosive sulfur emissions.

Yes, before installing the charger and connecting the cables, it is recommended to disconnect all loads from the battery. This helps to avoid the risk of electric arcing and ensures a safe installation.

No, it is essential not to cut the charger's connection cables. The cables are sized to ensure safe and efficient operation. Any modification could compromise the device's safety and performance.

Mastervolt guarantees the proper operation of this device for a period of two (2) years. This warranty is valid only if the charger is installed and used strictly in accordance with the instructions provided in the user manual.

The warranty for the Mastervolt EasyCharge 10A charger is limited to the cost of parts for replacement or repair of the device. It is important to note that labor and shipping costs are not covered under this warranty.

The Mastervolt EasyCharge 10A charger LED indicators show the charging status:

RED LED on (GREEN LED off): Battery is charging (REGENERATION or BULK stage).RED LED on (GREEN LED on): Charger is in ABSORPTION stage.RED LED off (GREEN LED on): Battery is fully charged (FLOAT stage).RED LED on (GREEN LED on) in FLOAT: Battery is fully charged, but a load is drawing current.No LED lit: Charger is in MAINTENANCE mode (powered down to save energy), or AC power is missing, or there is an internal fault.