Moduł wyzwalacza LUX RS232

The Garmin LUX RS232 Trigger module (010-04446-00) is used to enable triggering (activation or deactivation) of predefined "Scenes" stored in the Lumi-Link Command Center via external RS-232 commands.

Yes, the Garmin LUX RS232 Trigger module (010-04446-00) is specifically designed to work in conjunction with the Lumishore Lumi-Link Command Center to trigger its lighting scenes.

Yes, the triggers function independently of the multifunction display (MFD) or connected smart device. Scenes can therefore be triggered even if the MFD or smart device is off or on.

The RS-232 communication parameters for this module are as follows:

Baud rate: 38400Data bits: 8Parity: NoneStop bits: 2

To trigger a scene via RS-232, you must send the letter "T" followed by the desired trigger number. For example, to trigger port number 12, the command to send would be T12.

The RS-232 module enables access to the Lumi-Link Command Center's triggering capabilities. The Lumi-Link system can manage up to 15 distinct triggers, each corresponding to a specific scene.

The RS-232 module connects directly to the Lumi-Link Command Center via the power and trigger port connections. It is critical to connect each color-coded wire together and ensure all connections are isolated from one another. If the device is installed in a wet area, all connections must be sealed against moisture.

The technical documentation states that if the module is installed in a wet area, all connections must be made watertight. This implies that the module itself is not inherently watertight and requires adequate protection of connections in marine or humid environments.

No, the Garmin LUX RS232 Trigger module (010-04446-00) is specifically designed to interact with the Lumishore Lumi-Link Command Center and is not compatible with other lighting systems.

A "Scene" is a predefined lighting configuration stored in the Lumi-Link Command Center. It represents a specific set of lights and colors that can be activated or deactivated by an external trigger, such as this RS-232 module.

When creating or modifying a scene in the Lumi-Link Command Center, you can assign it a "trigger port number." To do this, select the trigger port icon (usually located in the top-right corner of the interface) and choose a number before saving the scene.

The RS-232 trigger module is identified by the Garmin part number 010-04446-00. In Lumishore’s technical documentation, it is also listed with the part number (PN) 60-0411.

No, this module is designed to trigger preconfigured "Scenes" in the Lumi-Link Command Center. It does not allow direct control of individual lights; individual light control is managed by the Lumi-Link Command Center itself.

When momentary switches are used directly with the Lumi-Link Command Center (instead of the RS-232 module), a voltage of +3 to +24 volts must be applied to the corresponding trigger wire. This applies to the compatibility of the Lumi-Link's global trigger system.

The RS-232 module uses specific digital commands (e.g., "T12") to trigger scenes. The binary connection method mentioned in the documentation refers to directly using the 4 trigger wires from the Lumi-Link Command Center with a digital switch to extend to 15 triggers, which is an alternative method to using the RS-232 module.

The documentation does not mention any specific software configuration for the RS-232 module itself. The main configuration involves creating and assigning scenes in the Lumi-Link Command Center, as well as sending RS-232 commands with the specified communication parameters.

The 'harbor trigger port icon' is a graphical interface within the Lumi-Link Command Center software that allows the user to assign a specific harbor trigger port number to a scene during its creation or modification.

No, the Garmin LUX RS232, Trigger (010-04446-00) module is specifically designed to interact with Lumishore's Lumi-Link Command Center and is not intended to control other Garmin devices directly.

Using the RS-232 module allows triggering scenes via digital commands, offering potentially more sophisticated integration with external control systems. This enables managing up to 15 triggers programmatically, which is more flexible than momentary switches that are direct physical triggers.

The technical documentation describes the required connections for the module but does not specify whether cables are included. It states that the module connects directly to the Lumi-Link Command Center via power and trigger port connections.