Airmar P19 – Sondă traversantă din plastic 500W (77/200kHz) cu element înclinat (12°) – (8 pini)

The Garmin Airmar P19 transducer has a transmit power of 500W RMS, providing reliable and precise detection.

The Airmar P19 transducer operates on two frequencies: 77 kHz and 200 kHz. This dual-frequency setup provides versatility for fish detection and depth reading across different conditions.

Yes, the Garmin Airmar P19 transducer provides accurate depth and water temperature measurements.

This through-hull transducer has a depth detection capability of up to 274 meters (900 feet), depending on water conditions and the display unit used.

The Airmar P19 transducer provides a 45° beam width at 77 kHz for broader coverage and a 15° beam width at 200 kHz for finer detail on the seabed and fish.

The P19 transducer integrates a 12° tilted element. This fixed angle is designed to compensate for the hull deadrise angle, ensuring the sonar beam is horizontally oriented toward the bottom even if the hull is heeled. This optimizes echo return without requiring an external fairing block.

The Airmar P19 transducer has a low-profile design. It protrudes only about 5 mm (3/16") below the hull, reducing drag and interference during navigation.

Yes, the Airmar P19 transducer housing is made of robust plastic and complies with ABYC H-27, ensuring durability in the marine environment.

The Airmar P19 transducer, with its plastic housing, is recommended for installation on fiberglass or metal hulls. It is imperative never to install a plastic housing on a wooden hull, as wood swelling could crack the plastic.

The Airmar P19 transducer, with its 12° tilted element, is specifically designed for hulls with a deadrise angle between 8° and 15° at the mounting location. It is critical to match the transducer’s tilt angle to your hull’s deadrise angle for optimal performance.

For the installation of the Airmar P19 transducer, a 51 mm (2 in) hole must be drilled from the outside of the hull. For fiberglass sandwich-type hulls, a 60 mm (2-3/8 in) hole is required from the inside of the hull.

Yes, for optimal performance, the transducer must be installed in an area where the water flow under the hull is smooth, with minimal bubbles and turbulence. Avoid locations in line with or near water intakes or discharges, behind strakes, fittings, or any hull irregularities. Ensure the transducer is continuously submerged at all speeds and that the beam is not obstructed by the keel or propeller shaft. Do not install the transducer where the boat may be supported during towing, launching, lifting, or storage.

During installation, the arrow on top of the transducer must point toward the keel or the boat's centerline. This ensures the internal element angle of the transducer aligns with the deadrise angle of your hull for optimal performance.

No, it is strongly discouraged to use a fairing block with a plastic transducer housing like the P19. The protruding sensor would be vulnerable to damage in case of impact.

For a correct installation of the Airmar P19 transducer, a minimum vertical space of 95 mm (3-3/4 inches) is required inside the hull for the housing body, nut tightening and cable handling.

The Garmin Airmar P19 transducer is fitted with an 8-pin Garmin connector, designed to plug directly into compatible devices.

This transducer is compatible with Garmin fishfinders equipped with an 8-pin transducer port. This includes many models from the Garmin ECHOMAP, GPSMAP, and STRIKER series, as well as other traditional Garmin fishfinders. Please verify specific compatibility with your Garmin device model.

No, the Airmar P19 transducer is a solution designed for traditional depth sounders operating on fixed frequencies (77/200 kHz). It is not compatible with CHIRP technology, which uses a swept frequency range.

If you have any questions or issues with your Airmar P19 transducer, we recommend contacting Garmin customer support or your authorized dealer. They can provide technical assistance and specific advice.