Material de montaj (Panoptix™ PS70)

This mounting hardware is a set of accessories specifically designed for the secure and optimal installation of the downward-facing Panoptix PS70 through-hull transducer. It ensures durable mounting even in demanding marine conditions.

The mounting kit includes stainless steel through-hull components, essential for durability and corrosion resistance in a marine environment. A fairing block is also provided, along with an anti-rotation bolt.

The fairing block is supplied to allow the transducer to be installed on hulls with a deadrise angle of up to 20 degrees. It is designed to position the transducer parallel to the waterline, which is critical for maintaining sonar return accuracy at high operating speeds and to withstand hydrodynamic stresses.

The through-hole components included in this mounting hardware are made of stainless steel, ensuring excellent durability and corrosion resistance in a marine environment.

This mounting hardware is specifically designed for installing the Garmin Panoptix™ PS70 downward-facing through-hull transducer.

This mounting hardware is compatible with a variety of hull types, including fiberglass (with or without core) and metal. It can be installed according to the provided instructions for these materials.

The included fairing block is designed for use on hulls with a deadrise angle of up to 20 degrees. It allows aligning the transducer parallel to the waterline on an inclined hull surface.

If the hull drift angle exceeds 20 degrees, installation with the fairing block is not recommended. In this case, the transducer must be installed in a dedicated hull pocket. The fairing block and anti-rotation bolt are not used for installation in a hull pocket.

Yes, for optimal performance and to avoid potential damage to the device or the vessel, installation by a qualified marine technician is recommended.

Drill3 mm (1/8 in)18 mm wrench or adjustable wrench46 mm (1 13/16 in) wrench or adjustable wrench for nuts up to 50 mm (2 in)Marine sealant (flexible, fast-curing type for below waterline)Mild household detergent or rubbing alcoholSandpaperMasking tapeWaterproof electrical tapeWax

Yes, applying marine sealant is mandatory to ensure a perfect watertight seal and prevent any risk of water infiltration. The sealant must be applied between the fairing block and the hull, between the fairing block and the transducer, between the fairing block and the anti-rotation bolt cap, on the bolt holes and the transducer cable stem, between the stem and the hull nut, between the rings, the stem and the hull, and between the transducer and the hull pocket.

The arrows on the fairing block and on the transducer must point strictly forward. This ensures the transducer is aligned with the vessel’s direction for optimal performance.

The transducer must be mounted in clean (non-turbulent) water for optimal performance, away from elements creating bubbles or turbulence (straps, struts, fittings, water discharge outlets or inlets). It must not be mounted behind propellers or in their path on single-propulsion boats. On twin-propulsion boats, it should be mounted between the propulsions if possible. Avoid locations where it could be shaken during launching, towing, or storage. Do not install near the engine, in the engine room, or in any other hot area to prevent overheating and interference.

To avoid possible bodily injury, it is imperative to always wear safety glasses, hearing protection, and a dust mask when drilling, cutting, or sanding. Always check what is on the other side of the surface before drilling or cutting to avoid damaging the sailboat.

The anti-rotation bolt is mandatory for installations using the fairing block to prevent the transducer from rotating when the boat is underway, which could damage the hull. However, it is not used when the transducer is installed in a dedicated hull pocket.

Yes, it is necessary to update the Garmin chartplotter software when installing this device to ensure compatibility and optimal operation.

After marking the hole locations, drill a 3 mm pilot hole. Then use a spade bit or a 42 mm hole saw for the shaft hole, and an 18 mm drill bit for the anti-rotation bolt hole. It is critical to remove the core material plug and seal the exposed core with high-quality marine epoxy resin and allow it to cure before mounting the transducer to prevent water intrusion.

After marking the hole locations, drill a 3 mm pilot hole. Then use a 38 mm hole saw for the shaft hole and a 16 mm drill bit for the anti-rotation bolt hole. It is important to sand and clean the inside and the area around the holes after drilling.

Yes, Garmin mounting hardware (Panoptix™ PS70) is covered by Garmin’s standard warranty for its marine products and accessories. This warranty covers manufacturing and material defects.

The mounting kit for this Panoptix PS70 through-hull transducer includes all necessary installation accessories. It comprises stainless steel through-hull components, a fairing block, an anti-rotation bolt, and installation instructions.