Sondă Panoptix LiveScope LVS12

The Panoptix LiveScope LVS12 transducer is designed to connect directly to compatible Garmin chartplotters. Unlike other LiveScope transducers such as the LVS32 or LVS34, which require an external black housing module (GLS10), the LVS12 simplifies installation by integrating directly into your chartplotter.

The Garmin Panoptix LiveScope LVS12 transducer provides LiveScope forward and down views. These views enable real-time visualization of what is happening underwater, ahead of and directly beneath your boat, which is essential for fish and structure detection.

For optimal performance, several points must be considered when installing the LVS12 transducer:

Do not install the transducer in the propeller wash. On an outboard motor, install it on the side of the descending propeller flow (usually starboard). Choose a location where it will not be shaken during launching, hauling, or storage. Avoid installing it behind stringers, struts, fittings, water inlets or outlets, other through-hull transducers, or anything that could create air bubbles or cause turbulent water flow. Install it as close as possible to the boat's centerline. On twin-engine vessels, install it between the engines if possible.

For installing the transducer, the following tools are generally required:

Drill
4 mm (5/32 in) and 3.2 mm (1/8 in) drill bits
Masking tape
Phillips screwdriver #2
Marine sealant
32 mm (1 1/4 in) hole saw (optional)
Cable ties (optional)

Yes, the Panoptix LiveScope LVS12 transducer can be installed in several ways. The installation instructions detail procedures for mounting on an electric motor (on the shaft or directly on the motor) as well as for mounting on the boat’s transom. It is important to follow the specific recommendations for each type of installation to ensure optimal performance.

Yes, it is mandatory to update the software of your Garmin chartplotter when you install the Panoptix LiveScope LVS12 transducer. If your chartplotter has Wi-Fi technology, you can perform the update via the ActiveCaptain™ app on a compatible Android™ or Apple device. If your chartplotter does not have Wi-Fi, the update is done using an SD card and a Windows computer.

The dimensions of the Panoptix LiveScope LVS12 transducer are as follows:

Length: 113 mm (4.45 in)Height: 92 mm (3.6 in)Width: 23 mm (0.9 in)

Before calibrating the compass, the depth sounder must be installed on the shaft far enough from the electric motor to avoid magnetic interference, and deployed in the water. The calibration must be of sufficient quality to activate the internal compass. For best results, using a heading sensor such as the SteadyCast™ is recommended. The general procedure is as follows:

From a valid sonar view, select MENU > Sonar Settings > Installation. If needed, select Use AHRS to activate the AHRS sensor. Select Calibrate Compass. Follow the on-screen instructions, performing a full 1.5 rotations of the boat during calibration.

The Panoptix LiveScope LVS12 transducer stands out for its ability to connect directly to certain compatible Garmin chartplotters without requiring an external black box (sonar module) like the GLS10. This greatly simplifies installation and wiring. It provides both LiveScope forward and down views.

The LiveScope LVS12 transducer provides two primary sonar views:

LiveScope front view: Allows real-time viewing of fish and structures ahead of your boat. LiveScope downward view: Allows real-time viewing of fish and structures directly beneath your boat.

For installing the Garmin LVS12 transducer, you will generally need the following tools:

Drill4 mm (5/32 in) and 3.2 mm (1/8 in) drill bitsMasking tapePhillips screwdriver size #2Marine sealantHole saw 32 mm (1 1/4 in) (optional)Cable ties (optional)

When installing on an electric motor, it is crucial to:

Secure the transducer cable along the shaft or another safe location to prevent damage. Orient the mounting bracket of the electric motor shaft so that the narrow end of the angle is upward. Position the sloped side of the transducer toward the front of the electric motor. Route the cable so that it is not pinched when the motor is deployed or stowed.

Yes, the LVS12 transducer can be installed on the boat’s transom using the supplied mounting bracket. It is important to align the transducer’s line with the bottom of the transom for correct underwater alignment. For deep-V hulls, an extension bracket may be added to position the transducer lower below the waterline.

Yes, it is essential to update the software of your Garmin chartplotter after installing the LVS12 transducer to ensure compatibility and optimal performance. If your chartplotter has Wi-Fi technology, the update can be performed via the ActiveCaptain app. Otherwise, a memory card and a Windows computer can be used.

To calibrate the LVS12 sounder compass, follow these steps:

Ensure the transducer is installed far enough from the engine to avoid magnetic interference and is deployed in the water. From a compatible sonar view, select MENU > Sonar Setup > Installation. If needed, select Use AHRS to enable the AHRS sensor. Select Calibrate Compass. Follow the on-screen instructions, rotating your boat 1.5 times during calibration. For best results, using an external heading sensor such as the SteadyCast heading sensor is recommended.

The physical dimensions of the Panoptix LiveScope LVS12 transducer are 113 mm (length) x 92 mm (height) x 23 mm (width), approximately 4.45 x 3.6 x 0.9 inches.

To maintain the performance of your LiveScope LVS12 transducer, it is important to clean it regularly. Aquatic debris can build up quickly and reduce the device's effectiveness. To clean it, use a soft cloth and a mild detergent, then wipe it dry.

No, the Panoptix LiveScope LVS12 transducer is designed to connect directly to compatible Garmin chartplotters. It does not require an external black box (sonar module) like the GLS10, which simplifies installation.