Invertor Phoenix VE.Direct Schuko 24V/250W

The primary function of this inverter is to convert a 24V DC voltage, typically sourced from a battery, into 230V AC at a frequency of 50Hz. This enables powering domestic or marine electrical devices from a DC energy source.

The Victron Energy VE.Direct Schuko inverter (PIN241251200) provides a continuous output of 250W at an ambient temperature of 25°C. This output is reduced to 200W if the ambient temperature reaches 40°C.

This inverter model is equipped with a Schuko (CEE 7/4) type output socket.

The Victron Energy VE.Direct Schuko inverter (PIN241251200) requires a nominal input DC voltage of 24V. Its input voltage range is 18.4 V to 34 V.

Yes, this inverter is designed to be protected against output short-circuits and overheating, whether caused by overload or high ambient temperature. It also includes other protections to ensure its reliability.

ECO mode is an energy-saving feature. When the inverter is in ECO mode, it enters standby if the connected load drops below a predefined value (minimum 15W). It then powers back on for a short period (default every 2.5 seconds) to check if the load has increased. If the load exceeds a certain level, the inverter remains on. This mode reduces the device's idle power consumption.

The standby power consumption of the VE.Direct Schuko inverter (model 24V) is 6W in normal operating mode. In ECO mode, this consumption is reduced to 1W.

Yes, this inverter has a high start-up capacity, making it suitable for powering inductive loads. This includes devices such as power converters for LED lamps, halogen lamps, or certain power tools that require a power surge at start-up.

The inverter includes multiple protections to ensure safe and reliable operation:

Output short-circuit protectionOverload protectionOver-voltage protection (high battery voltage)Under-voltage protection (low battery voltage)Over-temperature protectionExcessive DC ripple protection

The inverter is equipped with a VE.Direct communication port. To connect it to a computer, you will need a VE.Direct to USB interface cable. For smartphones, Apple and Android tablets, and other devices, a VE.Direct Bluetooth Smart dongle is required.

Via the VE.Direct port, you can fully configure the inverter. Options include:

Battery low-voltage alarm trigger and reset levels.
Battery low-voltage cut-off and restart thresholds, including dynamic cut-off (load-dependent).
Output voltage setting (210V to 230V).
Frequency setting (50 Hz or 60 Hz).
ECO mode activation/deactivation and its detection level.

The inverter's AC output voltage is adjustable between 210V and 230V. The output frequency can be set to 50 Hz or 60 Hz.

For the Victron Energy VE.Direct Schuko inverter (model 24V/250W), the minimum recommended battery capacity is 20 Ah.

Yes, a remote on/off switch can be connected to a dedicated two-pole connector. It is also possible to connect it between the battery positive terminal and the left contact of the two-pole connector, which may be useful for automotive applications, for example.

For optimal performance, the inverter must be installed on a flat surface. It is important to avoid any contact with water and not to expose it directly to sunlight. The ambient temperature must be between -20°C and 40°C. Ensure that at least 10 centimeters of free space is left around the inverter for adequate ventilation to prevent overheating.

Yes, this inverter is a Class I safety product, meaning the chassis must be grounded. A grounding point is located outside the product. The ground conductor must have at least half the cross-section of the conductors used for the battery connection.

The inverter is equipped with an internal DC fuse (30A for the 24V/250W model), which cannot be replaced by the user. If the DC cable length between the battery and the inverter exceeds 1.5 meters, an additional fuse or DC circuit breaker must be installed near the battery for enhanced protection.

No, it is imperative to never connect the AC output of the inverter to another AC power source, such as a domestic wall outlet or a generator. This could damage the inverter and pose safety risks.

The Victron Energy VE.Direct Schuko inverter (PIN241251200) provides continuous power of 250W at an ambient temperature of 25°C, or 200W at 40°C. It is designed to convert a 24V DC voltage, typically sourced from batteries, into 230V/50Hz AC power. This allows standard electrical devices to be powered on board a boat, in a vehicle, or in any other standalone installation. This model is specifically equipped with a Schuko (CEE 7/4) output socket.

The VE.Direct Schuko inverter is equipped with a VE.Direct communication port for advanced configuration. It can be connected in two main ways:

To a computer: Use a VE.Direct to USB interface cable (sold separately).To a smartphone or tablet: Connect it to an Apple or Android device via a VE.Direct Smart Bluetooth dongle (sold separately).This connectivity provides access to a full range of settings, including battery low-voltage alarm trigger and reset levels, cut-off and restart thresholds, output voltage (210–230V) and frequency (50 or 60 Hz) adjustment, and ECO mode configuration to optimize power consumption.