Airmar P19 – Plastična prečna sonda 500W (77/200kHz) z nagnjenim elementom (12°) – (8 žic)

The Garmin Airmar P19 transducer has a transmit power of 500W RMS, providing reliable and precise detection.

The Airmar P19 transducer operates at two frequencies: 77 kHz and 200 kHz. This dual-frequency setup provides versatility for fish detection and depth reading across different conditions.

Yes, the Garmin Airmar P19 transducer provides accurate depth and water temperature measurements.

This through-hull transducer has a depth detection capability up to 274 meters (900 feet), depending on water conditions and the display unit used.

The Airmar P19 transducer offers a beam width of 45° at 77 kHz for broader coverage and 15° at 200 kHz for finer detail on the seabed and fish.

The P19 transducer features a 12° tilted element. This fixed angle is designed to compensate for your hull’s deadrise angle, ensuring the sonar beam is directed horizontally toward the seabed even if the hull is tilted. This optimizes echo return without requiring an external fairing block.

The Airmar P19 transducer has a low-profile design. It protrudes only about 5 mm (3/16") below the hull, minimizing drag and interference during sailing.

Yes, the Airmar P19 transducer housing is made of durable plastic and meets ABYC H-27 standards, ensuring durability in marine environments.

The Airmar P19 transducer, with its plastic housing, is recommended for installation on fiberglass or metal hulls. It is imperative never to install a plastic housing on a wooden hull, as wood swelling could fracture the plastic.

The Airmar P19 transducer, with its 12° tilted element, is specifically designed for hulls with a deadrise angle between 8° and 15° at the mounting location. It is critical to match the transducer’s tilt angle to your hull’s deadrise angle for optimal performance.

For installing the Airmar P19 transducer, drill a hole of Ø 51 mm (2 inches) from the outside of the hull. For fiberglass sandwich hulls, a hole of Ø 60 mm (2-3/8 inches) is required from the inside of the hull.

Yes, for optimal performance, the depth sounder must be mounted in an area where the water flow under the hull is smooth, with minimal bubbles and turbulence. Avoid locations in line or near water intakes or discharges, behind strakes, fittings, or any hull irregularities. Ensure the transducer is continuously submerged at all speeds and that the beam is not obstructed by the keel or propeller shaft. Do not mount the depth sounder where the boat could be supported during towing, launching, lifting, or storage.

During installation, the arrow on top of the transducer must point toward the keel or the boat’s centerline. This aligns the internal element’s angle with the deadrise angle of your hull for optimal performance.

No, it is strongly discouraged to use a fairing block with a plastic transducer housing like the P19. The protruding sensor would be vulnerable to damage from impacts.

For correct installation of the Airmar P19 transducer, a minimum vertical space of 95 mm (3-3/4 inches) is required inside the hull for the housing body, nut tightening, and cable handling.

The Garmin Airmar P19 transducer is equipped with an 8-pin Garmin connector, designed to plug directly into compatible devices.

This transducer is compatible with Garmin fishfinders equipped with an 8-pin transducer port. This includes many models from the Garmin ECHOMAP, GPSMAP, and STRIKER series, as well as other traditional Garmin fishfinders. Please verify compatibility with your specific Garmin device model.

No, the Airmar P19 transducer is a solution designed for traditional depth sounders operating on fixed frequencies (77/200 kHz). It is not compatible with CHIRP technology, which uses a swept frequency range.

If you have questions or issues with your Airmar P19 transducer, we recommend contacting Garmin customer support or your authorized dealer. They can provide technical assistance and specific advice.