Sonda GT15M-THF 20° - prečna CHIRP srednje frekvence

The Garmin GT15M-THF transducer is made of stainless steel, making it compatible with a wide range of hull materials. It can be installed on hulls made of:

FiberglassWoodCompositeAluminumSteelImportant precaution: If you install this transducer on an aluminum or steel hull, you must absolutely install the galvanic isolation components provided. Failure to do so will cause galvanic corrosion, which could lead to water ingress around the transducer.

The Garmin GT15M-THF transducer is preconfigured for a 20-degree angle. For optimal performance, it is designed for hulls with a deadrise angle between 17 and 24 degrees at the installation location. The deadrise angle is the measurement of the angle between a horizontal line and the outer hull at a given point.

To measure the deadrise angle of your hull, you can use:

A smartphone appA protractorA bevel gaugeA digital levelYou can also contact your boat manufacturer to obtain this information. It is crucial to check this angle precisely before drilling holes.

For optimal performance, the depth sounder must be mounted in an area of clean water, free from turbulence generated by propellers, keels, or other hull appendages. General recommendations are as follows:

Outboard and sterndrive boats: At the bow and near the motor(s).Inboard boats: At the bow and away from the propeller and propeller shaft.Step hulls: At the bow, in front of the first step.Long keel hulls: Slightly angled toward the bow, parallel to the centerline.Fin keel hulls: 25 to 75 cm (10 to 30 in) ahead of the keel and no more than 10 cm (4 in) from the centerline.Displacement hulls: Approximately one-third of the waterline length from the bow, and 150 to 300 mm (6 to 12 in) from the centerline.Avoid mounting it behind planking, frames, seams, water intakes, or exhaust outlets, or any feature that could create air bubbles or turbulence. The depth sounder must be parallel to the fore-aft axis of your vessel.

Yes, it is mandatory to update the software on your Garmin chartplotter when you install this depth sounder. For detailed instructions on updating the software, refer to your chartplotter’s user manual. These manuals are typically available on support.garmin.com.

Preparing a fiberglass sandwich hull is a critical step to prevent water intrusion and damage. Here are the steps to follow:

From the outside of the hull, drill a 3 mm (1/8 in) pilot hole at the chosen location for the transducer. Place masking tape over the pilot hole and the surrounding area on the outside of the hull to reduce the risk of gelcoat cracking. Use a 73 mm (2 7/8 in) hole saw to cut the transducer hole completely through the outer hull. From the inside of the hull, use a slightly larger hole saw to cut only the inner fiberglass skin and the core. Be careful not to cut the outer skin with this larger saw. Seal the core inside the hull using either fiberglass with resin or casting epoxy. If using epoxy, create a 73 mm (2 7/8 in) diameter cylinder as a spacer while the epoxy sets. Proper sealing of the core is essential to prevent water damage.

To ensure the longevity and proper operation of your Garmin GT15M-THF transducer, follow these precautions:

Cable handling: Never use the cable to lift or pull the transducer; this could damage it.Immersion: Always operate the transducer when submerged. Using it when exposed to air can cause heat damage.Never use solvents such as mineral spirits, acetone, methyl ethyl ketone (MEK), or similar products for cleaning, as they may permanently damage the transducer's surface. Do not use an electric sander or pressure washer.Location: To avoid interference and potential heat damage, do not install the transducer near the engine or in the engine room.

Cutting or splicing the transducer cable is strongly discouraged. This should only be done if you are connecting the transducer to a black box sonar module requiring bare-wire connections.

Warning: Cutting the transducer cable outside of this specific case may void your warranty.

The Garmin GT15M-THF transducer is made of stainless steel and is compatible with a wide range of hull materials. It can be installed on fiberglass, wood, composite, aluminum, and steel hulls. For metal hulls (aluminum or steel), it is essential to install the provided galvanic isolation components to prevent corrosion.

The main difference lies in the manufacturing material and compatibility with hull types:

The GT15M-THF is made of stainless steel and is compatible with fiberglass, wood, composite, aluminum, and steel hulls. It requires the installation of galvanic isolation components for metal hulls.The GT12M-THF is made of brass and is limited to fiberglass, wood, or composite hulls. It must not be installed on aluminum or steel hulls to avoid galvanic corrosion.

The Garmin GT15M-THF transducer is a pre-configured model at 20 degrees. For optimal performance, it is essential that the deadrise angle of the hull at the installation point is as close as possible to this angle. It is optimized for deadrise angles ranging from 17 to 24 degrees.

Yes, specific precautions are required when installing on aluminum or steel hulls to prevent galvanic corrosion and water ingress. You must install the included galvanic isolation components (hull isolator and thread isolator) as specified in the installation instructions. Failure to install these components can result in galvanic corrosion.

For installing the Garmin GT15M-THF transducer, you will need the following tools:

A drill and a 3 mm (1/8 in) bitAn adjustable wrench (up to 75 mm)Marine sealant (flexible, fast-curing type, for below the waterline)Mild household detergent or rubbing alcoholSandpaper and masking tapeWaterproof electrical tapeHole saws: 73 mm (2 7/8 in) for fiberglass hulls and 75 mm (3 in) for metal hulls.Additional items such as marine-grade epoxy resin or a file may be required depending on the hull type.

Yes, you must update the software on your Garmin chartplotter when you install this depth sounder. For software update instructions, refer to your chartplotter's owner's manual.

For optimal performance, the depth sounder must be mounted in an area of clean water, free from turbulence. Avoid zones behind frames, struts, fittings, water intakes or discharges, or anything that could create air bubbles. Here are some general guidelines:

On outboard or inboard/outboard motorboats, mount the depth sounder in front of and close to the motor(s).On inboard motorboats, mount the depth sounder in front of and away from the propeller and propeller shaft.On stepped hulls, mount the depth sounder in front of the first step.On long-keel hulls, mount the depth sounder slightly angled toward the bow, parallel to the centerline.On fin-keel hulls, mount the depth sounder 25 to 75 cm (10 to 30 in) in front of the keel and no more than 10 cm (4 in) to the side of the centerline.On displacement hulls, mount the depth sounder approximately one-third of the waterline length from the bow, and 150 to 300 mm (6 to 12 in) to the side of the centerline.Ensure the depth sounder is parallel to the bow-stern axis of your boat and will not be struck during launching, towing, or storage.

To avoid permanently damaging the transducer surface, do not use solvents such as white spirit, acetone, methyl ethyl ketone (MEK), or similar products for cleaning. Also, do not use an electric sander or pressure washer to clean the transducer.

For regular cleaning, a mild household detergent or isopropyl alcohol can be used.

Yes, when installing the depth sounder in a fiberglass hull, it is important not to overtighten the nut to avoid damaging the hull. The hull nut should be tightened using a 75 mm wrench or an adjustable wrench to secure the depth sounder. You can hold the depth sounder rod steady during tightening.

Preparing a fiberglass hull with core is crucial to prevent water ingress and serious damage to the boat. Here are the main steps:

Drill a 3 mm (1/8 in) pilot hole from the outside of the hull.Place masking tape around the pilot hole on the outside.Use a 73 mm (2 7/8 in) hole saw to cut the transducer hole through the entire hull.From inside the hull, use a slightly larger hole saw to cut only the inner fiberglass skin and core, taking care not to cut the outer skin.Seal the core inside the hull either with fiberglass and resin or with casting epoxy, creating a 73 mm (2 7/8 in) cylinder as a spacer so the epoxy cures.Sand and clean the hole after curing.

During installation, rotate the transducer from inside the hull until the arrow on top points toward the keel of the boat. This orientation is critical so that the internal angle of the transducer aligns correctly with your boat's deadrise angle, ensuring optimal performance.

In general, cutting or splicing the transducer cable is not recommended, as it may void your warranty. The only exception is if you are connecting the transducer to a black box sonar unit that requires bare-wire connections. In all other cases, avoid cutting the cable to prevent damage to both the cable and the transducer.

The Garmin GT15M-THF depth sounder is made of stainless steel. This material provides robustness and versatility, making it compatible with various hull types, including metal hulls, provided that the supplied galvanic isolation components are used.