Sonda gWind™ Race - izključno za dirke

The Garmin gWind™ Race wind transducer is an anemometric sensor designed specifically for racing sailing. It provides wind data with precision suited to regatta requirements, measuring wind speed and angle to optimize race strategy and polar calculations.

Straight 1-meter mast: Positions the sensor above the masthead to reduce turbulence errors.Three-blade propeller: Optimized for accurate true wind speed (TWS) measurements, even in light winds.Double tail fin: Ensures increased stability of the true wind angle (TWA), minimizing fluctuations caused by boat movements.Optical reading: Guarantees reliable performance at low wind speeds and excellent linearity for consistent data.

The gWind™ Race wind transducer is equipped with a three-blade propeller, specifically designed for precise measurement of true wind speed (TWS). This design is optimized to reliably capture wind data, even in light wind conditions, ensuring consistent and usable information for competitive sailing.

The straight 1-meter (3.3 ft) mast of the gWind™ Race sensor is a key element of its design. It positions the anemometric sensor above the masthead, significantly reducing turbulence errors caused by sails. This elevated position is crucial for obtaining undisturbed wind measurements, essential for accurate regatta data.

The gWind™ Race transducer features a dual-fin design that provides enhanced stability in true wind angle (TWA) measurement. This design minimizes fluctuations in wind angle data that could be caused by boat movements, ensuring more stable and reliable readings—critical for racing performance.

For maintenance of the gWind™ Race wind transducer, it is recommended to use a mild soap solution if necessary, then rinse with fresh water. It is important not to use harsh detergents or high-pressure water, as this could damage the device. It is also advisable to remove the transducer for prolonged storage.

No, the Garmin gWind™ Race transducer cannot operate autonomously. It requires the Garmin GND™ 10 black box (sold separately) to process and transmit its data. The GND™ 10 bridges the transducer and your boat’s NMEA 2000® network.

To use the gWind™ Race transducer, you must have the Garmin GND™ 10 black box (sold separately). The GND™ 10 is essential for transmitting data to an NMEA 2000® network. Once the data is on the NMEA 2000® network, it can be displayed on compatible Garmin chartplotters and Garmin marine instruments, such as the GMI™ 20.

Yes, the gWind™ Race transducer is compatible with NMEA 2000® networks. However, it does not connect directly. It transmits its data via the Garmin GND™ 10 black box, which bridges the data from the Nexus network to the NMEA 2000® network, enabling integration with NMEA 2000®-compatible equipment.

Yes, when the GND™ 10 box is connected to a computer via a USB cable, you can use the data from the connected wind sensors, including the gWind™ Race transducer, with third-party sailing programs such as Expedition and Adrena. Garmin's NexusRace™ software can also be used to calibrate advanced sensors.

Yes, it is possible to connect other Nexus devices to the network in addition to a gWind™ sensor. However, if you connect additional devices, you must provide a separate power supply connected directly to the Nexus power terminals.

The gWind™ Race transducer must be mounted on a horizontal surface at the top of the mast. It must be installed facing the bow of the boat, parallel to the central axis. If the surface is not horizontal, a suitable shim must be added to create a flat surface. Care must be taken when working at height.

To install the propeller, ensure the shaft aligns correctly with the slot on the propeller (the propeller bushing fits only one way onto the shaft). Press the propeller down until it is fully seated on the device. Then, install the adjustment screw to securely hold the propeller in place on the device.

To mount the bracket, use the bracket as a template to mark the pilot hole locations. Drill pilot holes using a 4.5 mm (11/64 in) drill bit. Finally, secure the mounting bracket to the surface using the supplied screws.

To secure the transducer:

Loosen the locking nut on the device by turning it counterclockwise by hand until it stops.Place the device into the mounting bracket by pushing it down and sliding it backward until it stops.Secure the device in the bracket by turning the locking nut clockwise by hand until it stops.Attach the safety clamp to the device to prevent the locking nut from loosening.

You must use the field-installable connector provided to create the correct cable length. Connect the finished end of the supplied loose cable to the wind transducer on the mast. Route the stripped end of the cable to the GND 10 location. Cut the cable, remove the housing, and strip the individual wires. Disassemble the connector, install the components (crimp screws, clamp ring, seal, sleeve) onto the cable, then connect each wire to the appropriate terminals (Green, Yellow, Bare wire, White). Screw the sleeve, slide the seal and clamp ring into place, then tighten the crimp screw. Finally, connect the assembled connector to one of the NEXUS ports on the GND 10.

If the sensor is not mounted exactly facing the bow of the boat, you must adjust the wind angle offset. On the connected marine instrument (e.g., GMI™ 20), go to the NMEA 2000® settings, select the device name (GND 10), then choose 'Wind Angle Offset'. Select the angle in degrees to adjust the orientation difference, considering the angle configured clockwise around the mast from the exact center of the bow (e.g., 90 degrees for starboard, 270 degrees for port).

Yes, the Garmin gWind™ Race transducer is covered by Garmin’s limited consumer warranty. This warranty provides you with specific legal rights, and you may have other legal rights that vary by state or country.

Garmin’s limited warranty states that non-aviation products are warranted against defects in materials and workmanship. For a full understanding of your rights and warranty terms, consult your state, country, or province’s laws and Garmin’s official warranty documentation.