Modul in sonda StructureScan® 3D

NAVICO's StructureScan® 3D module is an advanced underwater imaging solution that uses multi-beam sonar technology. It provides anglers with a detailed three-dimensional view of fish, structures, and bottom contours, with a 180-degree perspective beneath the boat.

This system integrates several key features to optimize underwater detection:

A three-dimensional view of structures and fish. The SelectScan™ Target Identification function automatically shades fish hides and suspended targets in a contrasting color. A multi-beam sonar imaging system for extended coverage.

The StructureScan® 3D module operates at a frequency of 455 kHz for its SideScan and DownScan capabilities.

The SideScan has a maximum range of 365 meters total, which is 182 meters on each side of the boat.

In Downscan mode, the system can reach a maximum depth of 60 meters.

For optimal efficiency and maximum detection performance, the recommended cruising speed is 16 km/h or less.

The system can operate at higher speeds, though optimal performance is at lower speeds:

SideScan: Maximum speed of 56 km/h, with object marking capability up to 24 km/h.
Downscan: Maximum speed of 88 km/h, with object marking capability up to 56 km/h.

The kit includes the following items:

The StructureScan® 3D module.Installation screws.A 4-meter (15 ft) Ethernet cable.A 2-meter (6.6 ft) power cable.A fuse and its fuse holder.The StructureScan® 3D transducer.

The StructureScan® 3D module is CE-certified (in accordance with EMC Directive 2014/30/EU) and complies with Radio Equipment Directive Level 2 (2014/53/EU).

The power LED indicates the system status:

OFF: No power.ON - Red: The system is booting up.ON - Green: The system is operating normally.Flashing Red/Green: Indicates a software error, requiring a restart of the unit.

The LED on the transducer indicates its operational status:

OFF: The depth sounder is not operational.FLASHING (every second) - Green: The system is searching for a bottom signal.ON - Green: The system is operational and has detected a bottom signal.

The SelectScan™ Target Identification function automatically shades fish arches and suspended targets in a contrasting color, making them easier to detect and identify on screen.

The StructureScan® 3D module is designed to integrate with the following compatible multifunction displays:

Lowrance HDS Gen3Simrad NSS Evo2Simrad NSS Evo3Simrad NSO Evo2

No, the StructureScan® 3D is specifically compatible with Lowrance HDS Gen3, Simrad NSS Evo2, NSS Evo3, and NSO Evo2 series. It is designed to integrate seamlessly with these systems.

For the installation of the transducer, you will need the following tools and supplies (not included):

A drill.A screwdriver (Phillips head).Appropriate drill bits.High-quality marine adhesive/sealant, suitable for use above or below the waterline.

The StructureScan® 3D transducer can be mounted on the boat's transom or directly on the hull. The included mounting kit is suitable for these mounting types.

A 33 mm (1.3 in) hole diameter is required for the transducer cable to pass through the hull.

The mounting kit includes:

3 mounting screws for transom mount #10 x 1-1/4".3 flat washers #10 for transom mount screws.1 M6 x 40 mm bracket assembly bolt.1 M6 bracket assembly washer.1 M6 bracket assembly rubber spring washer.1 M6 bracket assembly nylon locking bolt.6 M4 x 8 mm transducer mounting screws.6 M4 transducer mounting washers.2 cable ties.

Yes, it is mandatory to use a high-quality marine adhesive/sealing product for all transducer installations, whether above or below the waterline, to ensure watertightness and protection.

If sonar data appears erased or the same color, you should try lowering your screen contrast or changing the color palette used for sonar display.