Mastervolt EasyCharge 6 A, 1 output, UK plug

The Mastervolt EasyCharge 6A charger delivers a maximum charge current of 6 amperes (A).

This charger is compatible with a wide range of 12V lead-acid batteries, including:

Flooded (acid) batteriesGel batteriesAGM batteriesSpiral batteriesIt is not designed to charge non-rechargeable batteries.

Yes, the Mastervolt EasyCharge 6A charger is designed for demanding environments. It features a fully sealed, epoxy-filled, non-corrosive housing, giving it an IP68 protection rating. This makes it resistant to water, salt, shocks, and vibrations, allowing installation in exposed locations.

For optimal installation, the charger must be mounted on a solid vertical surface that is heat-resistant, with the connectors pointing downward. Ensure no objects are within a 20 cm radius around the charger to allow proper hot air dissipation. The charger should be placed as far from the battery as the DC cables allow, and never directly above batteries to avoid corrosive sulfur emissions.

The Mastervolt EasyCharge 6A charger operates within an ambient temperature range of -20°C to 50°C. It delivers full power up to 40°C.

The Mastervolt EasyCharge 6A charger is recommended for batteries with a capacity between 20 Ah and 120 Ah.

The Mastervolt EasyCharge 6A charger integrates a 5-step automatic charging process to optimize battery lifespan and ensure a full charge:

Equalization: The charger checks connections and the battery's ability to accept charge, applying a low current if the battery is deeply discharged.Bulk: The charger delivers its maximum current to rapidly charge the battery from 0 to 75%.Absorption: The maximum charging voltage is reached and the current gradually decreases until the battery is fully charged at 100%.Float: The battery is fully charged. The charger stabilizes the battery voltage at 13.3 V for a period, then shuts off.Maintenance: The charger monitors battery state and restarts a full cycle if voltage drops below 12 V or if 14 days have elapsed since the last charge.

To connect the charger to your battery, follow these steps:

Start with the non-common terminal of the battery. Connect the RED terminal of the charger to the POSITIVE terminal (+, P, POS) of the battery. Then connect the BLACK terminal of the charger to the NEGATIVE terminal (NEG, N, –) of the battery.

The Mastervolt EasyCharge 6A charger is equipped with multiple protections to ensure safe use:

Spark protectionShort-circuit protectionReverse polarity protectionOvervoltage protectionCurrent limitingOver-temperature protection

No, the Mastervolt EasyCharge 6A-1 model is designed specifically for 12V battery systems only.

The Mastervolt EasyCharge 6A charger has dimensions of 89 mm (length) x 163 mm (width) x 63 mm (depth). Its weight without cable is 1.8 kg.

No, it is recommended not to cut the charger's connection cables. This could affect the device's performance or safety.

The Mastervolt EasyCharge 6A charger accepts an AC input voltage of 120/230 V (range 90–265 V) at a frequency of 50/60 Hz.

The Mastervolt EasyCharge 6A model with SKU 43310602 is supplied with a UK plug (BS1363 type G).

The Mastervolt EasyCharge 6A charger comes with a two (2) year warranty. This warranty is valid provided the device is installed and used in accordance with the manual instructions. It is limited to the cost of replacement parts or repair of the device.

Yes, it is mandatory to disconnect all battery consumers before installing the charger.

No, the Mastervolt EasyCharge 6A-1 model has a single isolated charge output.

Yes, provided the starter battery is a 12V lead-acid battery (flooded, gel, AGM or spiral) and its capacity is within the recommended range of 20 to 120 Ah, the Mastervolt EasyCharge 6A charger can be used to recharge it.