Sonda GT56UHD-TR - električni motori Garmin Force® / Force® Pro

Yes, to ensure optimal performance and to avoid potential injury or damage to the device or your vessel, installation by a qualified marine technician is strongly recommended. It is imperative to strictly follow the mounting instructions.

Yes, a medium-strength thread locking compound, such as LOCTITE 243™, is absolutely required on the threads of the four mounting holes located on the top of the propeller motor. This ensures a watertight and secure connection between the shaft base and the propeller motor, preventing water ingress and potential damage to the motor.

The Garmin GT56UHD-TR is a transducer replacement kit designed specifically for Garmin Force® and Force® Pro electric motors. Its main function is to maintain the integrity and sonar performance of these motors, ensuring the continuity of UHD (Ultra High Definition) sonar capabilities essential for detecting structures and fish.

The Garmin GT56UHD-TR is a transducer replacement kit. It is designed to replace an existing transducer on Force® and Force® Pro electric motors, not for a complete initial installation of the transducer on a boat.

The Garmin GT56UHD-TR is specifically designed to be compatible with Garmin Force® and Force® Pro electric motors. It is not intended for use with other Garmin motor models or brands.

Yes, it is necessary to update the Garmin chartplotter software when installing this depth sounder to ensure optimal performance and full compatibility.

Yes, if the depth sounder cable is not long enough to reach the chartplotter, you can add a Garmin extension cable (Garmin part number 010-11617-42 or 010-11617-32). However, to avoid signal degradation, it is recommended not to extend the cable by more than 9 meters (30 feet).

For replacing the transducer, you will need the following tools:

Phillips screwdriver #2 and #33 mm and 4 mm hex bits or hex wrenches (a 4 mm ball-end hex bit is highly recommended due to the angle of some screws)Torque wrenchMedium-strength thread locking compound, such as LOCTITE 243™Compressed air can or air compressor

To achieve the best possible performance and avoid potential injury or damage to the device or the boat, installation by a qualified marine installer is recommended. It is important to read all instructions and ensure you have the necessary tools and skills to perform the service correctly.

Before any manipulation or work on the propeller, propeller motor, electrical connections, or electronic housings, it is imperative to always disconnect the motor from the battery to prevent serious injury or death. Additionally, be aware of the risk of pinching or crushing due to moving parts when stowing or deploying the motor.

Yes, the use of a medium-strength thread-locking compound, such as LOCTITE 243™, is mandatory. It must be applied to the threads of the four threaded holes located on top of the propeller motor. This is crucial to maintain a watertight connection between the shaft base and the propeller motor, and to prevent water infiltration that could damage the motor.

Yes, new O-rings of various sizes (e.g., 78 mm and 36 mm) and grease packets are included in the replacement kit. The grease must be applied to the new O-rings before placing them into the corresponding grooves on the shaft base and on top of the propeller motor. This ensures proper sealing and water protection.

When routing the cables, always pull on the cable itself, not on the cable connectors. The data cable connector is fragile and may break if pulled. It is also recommended to straighten, align, and bundle the cables with tape if they are not already, so they pass smoothly through the shaft.

No, the cables connected to the depth sounder must never be cut. Cutting the depth sounder cables voids the product warranty. If the cable is too short, an official Garmin cable extension must be used.

You must use the new screws, washers, O-rings, and other parts supplied in the replacement kit. The old screws, washers, and gaskets must be discarded. Using new parts is essential to ensure the watertightness and durability of the installation.

Before you can replace the sensor, you must prepare the engine by performing the following actions:

Disconnect the engine from the power source.Open the shaft housing.Remove the cables inside the shaft housing.Disconnect the sensor cable from the shaft housing.Remove the shaft housing.Remove the shaft from the steering system.

After preparing the motor by removing the shaft from the steering system, the steps to remove the existing depth sounder are:

Remove the skeg and the nose cone from the propeller motor.Remove the propeller motor from the shaft.Remove the depth sounder from the nose cone.It is important to follow these steps carefully to avoid damaging the components.

After removing the existing probe, the key steps to install the replacement probe are:

Install the new probe in the nose cone, using the new neoprene pad, new screws, and provided washers.Apply grease to the O-rings and thread-locking compound to the mounting screws.Install the nose cone and skeg onto the propeller shaft.Make sure to use all new parts provided in the kit and follow the torque specifications.