Rafmagnsrofi Contura vatnsþéttur 12 V DC – Hvítur 8 staða

The BLUE SEA Contura 8-position circuit breaker panel (reference 8271-BSS) has overall dimensions of 238.00 mm wide by 108.00 mm high (9-3/8 x 4-1/4 inches). Its depth is 69.90 mm (2-3/4 inches).

Yes, this display is designed to be waterproof. Its front panel has an IP66 rating, providing protection against powerful water jets, salt spray, rain, hose-downs, and brief immersions. It is suitable for deck-mounted applications.

The panel includes eight default 15 amp push-button circuit breakers. Each circuit breaker is protected by a waterproof cap, and each Contura ON-OFF switch is equipped with a power indicator LED.

The panel is constructed from 2.54 mm (0.100 inch) thick 5052-H32 aluminum. It undergoes chemical treatment compliant with MIL-SPEC C-5541, followed by a two-part textured polyurethane finish in Arctic White. This construction provides durability and corrosion resistance in marine environments.

Each LED indicator light, integrated into the switch, consumes 18 milliamps. These LEDs have an estimated lifespan of 100,000 hours at half-life.

The five main functions of this marine electrical panel are:

Power distribution.Protection of circuits (wires).ON/OFF switching of circuits.Indication of status (circuit under power).

The panel is supplied with a mounting gasket, mounting screws, and a selection of 60 basic circuit labels to customize the identification of each switch.

Yes, this distribution panel is designed to operate with 12 Volt DC or 24 Volt DC electrical systems.

For 12 Volt DC systems, the maximum capacity per switch and circuit breaker is 20 amperes. For 24 Volt DC systems, the maximum capacity is 15 amperes per switch and circuit breaker. The total cumulative capacity of the panel is 45 amperes.

No, this panel must not be installed in explosive environments such as gasoline engine rooms or battery compartments. The panel’s switches are not protected against ignition.

To ensure the front face of the panel is water-resistant, it must be properly sealed to the dashboard surface. The included sealing gasket must be placed between the panel and the mounting surface, and the panel must be firmly screwed in. Ensure all surfaces are clean and free of debris.

Before starting the installation, it is imperative to disconnect the main positive cable from all batteries to eliminate any risk of short-circuit. You must also unplug the AC power cord from the dock to prevent any risk of electrocution due to AC wiring near the DC distribution panel.

The cutting template for panel 8271/8371 specifies a cutout of approximately 218.95 mm (8.620") in width and 108.46 mm (4.270") in height for the main section. Mounting centers are 216.90 mm x 86.90 mm (8-17/32 x 3-13/32 inches). It is recommended to use the provided template for precise cutting.

The positive power wire (red) must be sized based on the total amperage of the circuits routed through the panel. The panel's total cumulative capacity is 45 amperes. It is recommended to size the positive power wire for the panel's full capacity, which in most cases will require at least an 8 AWG wire for a 3% voltage drop over a 10-foot length in a 12-volt system. Refer to the wire sizing chart for other scenarios.

Each negative wire (yellow) from secondary circuits must be connected to a DC negative bus, such as a Blue Sea Systems PN 2301 busbar or MiniBus PN 2304.

A positive wire (red) from each secondary circuit must be connected to the load terminal of the corresponding switch on the panel.

A set of 60 basic labels is provided with the panel. Select the appropriate label for each circuit and apply it to the recessed area provided on the front face of the panel.

Blue Sea Systems offers a satisfaction guarantee. Any Blue Sea Systems product a customer is not satisfied with can be returned for a refund or replacement at any time.

Yes, this Blue Sea Systems waterproof electrical distribution panel is designed to comply with the standards and recommended practices of the American Boat and Yacht Council (ABYC) for small boats (section E-9), as well as with the U.S. Code of Federal Regulations 33, Part 183, Subpart I, regarding electrical systems on boats.