Airmar B619 – 500W (77/200kHz) gegnfarandi málmplata úr bronsi með hallandi (20°) þáttur – 8 stiftur

The Garmin Airmar B619 is a bronze through-hull transducer at 500W, operating on 77/200 kHz frequencies. It features a 20° tilted ceramic element and is designed for depth and temperature sensing. Its low-profile design minimizes drag, protruding only 5 mm (0.2 in) from the hull.

The B619 transducer has a power output of 500W and operates at two frequencies: 77 kHz and 200 kHz.

The Garmin Airmar B619 transducer can provide reliable data up to a maximum depth of 274 meters (900 feet).

The B619 transducer offers a 45° beam angle at 77 kHz and a 15° beam angle at 200 kHz, providing coverage suited to various navigation and fishing conditions.

Yes, the Garmin Airmar B619 transducer is designed for depth and water temperature detection.

The Airmar B619 transducer, with its bronze construction, is ideal for fiberglass and wooden hulls.

The B619 transducer features a 20° tilted element, making it specifically suited for hulls with a deadrise angle (deadrise) between 16° and 24°.

No, the B619 transducer with its bronze housing must never be installed on metal hulls. This is due to the risk of electrolytic corrosion that could damage both the transducer and the hull.

The Garmin Airmar B619 transducer is equipped with an 8-pin connector, ensuring direct integration with compatible Garmin systems.

The B619 transducer is designed for direct integration with compatible Garmin systems. It is recommended to verify specific compatibility with your Garmin display or fishfinder model.

To install the B619 transducer, a hole of Ø 51 mm (2 inches) must be drilled through the outer hull.

The B619 probe's Tilted Element™ technology compensates for the vessel's deadrise angle. This ensures the sonar beam is vertically oriented, providing more accurate depth readings and stronger echo returns, even at high speeds.

For optimal performance, the transducer must be installed in an area where the water flow under the hull is smooth, with minimal bubbles and turbulence, especially at high speed. Avoid areas aligned with water intakes, discharges, behind strakes, fittings, or any hull irregularities. The beam must not be obstructed by the keel or propeller shaft.

Yes, several precautions must be observed:

Never install the bronze transducer on a metal hull to avoid electrolytic corrosion. Ensure the transducer’s tilt angle (20°) matches the hull’s deadrise at the mounting point. Apply a suitable marine sealant for below-waterline applications. Never pull, carry, or hold the transducer by its cable. Immediately check for leaks once the boat is launched.

The Garmin Airmar B619 transducer can be installed on hulls with a maximum thickness of 64 mm (2.50 inches).

Due to its low-profile design, the B619 transducer protrudes only 5 mm (0.2 in) from the hull, minimizing drag.

During installation, it is crucial that the arrow on the top of the transducer points toward the keel or the boat's centerline. This ensures the internal element's angle is correctly aligned with the deadrise angle of your hull for accurate readings.

For installation of the B619 transducer, a minimum vertical space of approximately 95 mm (3-3/4 inches) is required inside the hull to accommodate the transducer body and allow for nut tightening.

Before installation, the area around the hole, both inside and outside the hull, must be sanded and cleaned. This ensures proper adhesion of the marine sealant. Any petroleum residue must be removed with a mild detergent or a weak solvent (such as alcohol) before sanding.

Yes, the B619’s bronze construction makes it particularly well-suited and resistant to marine environments, including saltwater. For saltwater installations, applying a water-based antifouling coating is mandatory to maintain performance.