Sond GT56UHD-TR - rafknúnar vélar Garmin Force® / Force® Pro

Yes, to achieve the best possible performance and to avoid potential injuries or damage to the device or your vessel, installation by a qualified marine installer is strongly recommended. It is imperative to strictly follow the mounting instructions.

Yes, a medium-strength thread locking compound, such as LOCTITE 243™, is absolutely required on the threads of the four mounting holes located on top of the propeller drive motor. This ensures a watertight and secure connection between the shaft base and the propeller drive motor, preventing water ingress and potential damage to the motor.

The Garmin GT56UHD-TR is a transducer replacement kit designed specifically for Garmin Force® and Force® Pro electric motors. Its primary function is to maintain the integrity and sonar performance of these motors, ensuring the continuity of UHD (Ultra High Definition) sonar capabilities essential for detecting structures and fish.

The Garmin GT56UHD-TR is a transducer replacement kit. It is designed to replace an existing transducer on Force® and Force® Pro electric motors, not for a first-time complete installation of the transducer on a boat.

The Garmin GT56UHD-TR is specifically designed to be compatible with Garmin Force® and Force® Pro electric motors. It is not intended for use with other Garmin motor models or brands.

Yes, it is necessary to update the software of your Garmin chartplotter when installing this depth sounder to ensure optimal performance and full compatibility.

Yes, if the depth sounder cable is not long enough to reach the chartplotter, you can add a Garmin extension cable (Garmin part number 010-11617-42 or 010-11617-32). However, to avoid signal degradation, it is recommended not to extend the cable by more than 9 meters (30 feet).

For the replacement of the transducer, you will need the following tools:

Phillips screwdriver size #2 and #33 mm and 4 mm hex bits or wrenches (a 4 mm ball-head hex bit is highly recommended due to the angle of some screws)A torque wrenchMedium-strength thread-locking compound, such as LOCTITE 243™Compressed air from a can or an air compressor

To achieve the best possible performance and avoid potential injuries or damage to the device or the boat, installation by a qualified marine installer is recommended. It is important to read all instructions thoroughly and ensure you have the necessary tools and skills to perform the service correctly.

Before any handling or work on the propeller, propeller motor, electrical connections, or electronic housings, it is imperative to always disconnect the motor from the battery to prevent serious injury or death. Additionally, be aware of the risk of crushing or pinching due to moving parts when stowing or deploying the motor.

Yes, the use of a medium-strength thread-locking compound, such as LOCTITE 243™, is mandatory. It must be applied to the threads of the four threaded holes located on the top of the propeller drive. This is critical to maintain a watertight connection between the shaft base and the propeller drive, and to prevent water infiltration that could damage the drive.

Yes, new O-rings of various sizes (e.g., 78 mm and 36 mm) and grease sachets are included in the replacement kit. The grease must be applied to the new O-rings before placing them in the corresponding grooves on the shaft base and on top of the propeller motor. This ensures proper sealing and protection against water.

When routing the cables, always pull on the cable itself and not on the cable connectors. The data cable connector is fragile and may break if pulled. It is also recommended to straighten, align, and bundle the cables with adhesive tape if they are not already, so they pass smoothly through the mast.

No, cables connected to the depth sounder must never be cut. Cutting the depth sounder cables voids the product warranty. If the cable is too short, an official Garmin cable extension must be used.

You must use the new screws, washers, O-rings, and other parts supplied in the replacement kit. The old screws, washers, and gaskets must be discarded. Using new parts is essential to ensure watertightness and the durability of the installation.

Before you can replace the transducer, you must prepare the engine by performing the following actions:

Disconnect the engine from the power source.Open the shaft housing.Remove the cables inside the shaft housing.Remove the transducer cable from the shaft housing.Remove the shaft housing.Remove the shaft from the steering system.

After preparing the motor by removing the shaft from the steering system, the steps to remove the existing depth sounder are:

Remove the skeg and the nose cone from the propeller motor.Remove the propeller motor from the shaft.Remove the depth sounder from the nose cone.It is important to follow these steps carefully to avoid damaging the components.

After removing the existing depth sounder, the key steps to install the replacement depth sounder are:

Install the new depth sounder in the nose cone, using the new neoprene pad, new screws, and new rings provided.Install the propeller drive on the shaft, applying grease to the O-rings and thread-locking compound to the mounting screws.Install the nose cone and skeg on the propeller drive.Make sure to use all the new parts provided in the kit and follow the tightening instructions.