Umbreyta 48/5000 Smart

The Victron Energy Inverter 48/5000 Smart is designed to deliver a continuous power output of 5000 VA (4000 W) at an ambient temperature of 25°C. This power is provided with high efficiency.

This inverter can support a peak power of up to 10 000 W. This capacity is essential for starting inductive loads or devices requiring high inrush current, such as refrigeration compressors or electric motors.

The inverter produces a pure sine wave. This signal quality is critical for the proper operation of sensitive electronic equipment, ensuring stable and disturbance-free power supply.

Yes, the inverter features an ECO mode. In this mode, the device switches to standby when the connected load drops below a predefined threshold, significantly reducing energy consumption. In ECO mode, the no-load power consumption is only 3.2 W.

The inverter is equipped with multiple protections to ensure its reliability and the safety of your installation:

Short-circuit protection on the output.Overload protection.Overheat protection, whether due to overload or high ambient temperature.Protection against excessively high or low battery voltages.Protection against excessive DC ripple.

The inverter offers several remote monitoring and configuration options:

Via the VE.Direct communication port, which can be connected to a computer (requires a VE.Direct to USB cable) or to Apple and Android smartphones/tablets (requires a VE.Direct Bluetooth Smart dongle).Thanks to the built-in Bluetooth, allowing direct connection with the VictronConnect app on your smartphone or tablet.By integrating it into the Victron VRM portal (Victron Remote Management) via a GX device (not included), for comprehensive power system control.

The Victron Energy Inverter 48/5000 Smart is specifically designed to operate with a 48 V DC input voltage. It is essential to ensure your battery bank provides this voltage.

You can configure the inverter's AC output voltage between 210 V AC and 245 V AC. The output frequency is also adjustable, allowing you to select either 50 Hz or 60 Hz based on your requirements and regional standards.

Yes, the inverter is equipped with a dedicated bipolar connector for connecting a remote on/off switch. Alternatively, the left contact of this connector can be connected to the battery positive, which is useful for automotive applications (for example, by wiring it to the ignition switch).

The inverter allows precise configuration of low battery alarm and cutoff voltage levels. It also features a dynamic cutoff function, where the cutoff level adjusts based on load, providing optimized battery autonomy management.

For optimal performance, the inverter must be installed on a flat surface. Recommended mounting options are:

Base mounting (on the floor or on a shelf).Vertical wall mounting, with the fan positioned at the bottom.Horizontal wall mounting.It is important to avoid ceiling mounting (inverted) or vertical wall mounting with the fan at the top.

To ensure trouble-free operation and prevent overheating, it is imperative to leave a clearance of at least 10 centimeters around the inverter. The ventilation vents must never be obstructed to allow adequate airflow.

To ensure the inverter's durability and proper operation, comply with the following environmental conditions:

Avoid any contact with water, rain, or moisture.Do not place the device in direct sunlight.The ambient temperature must be between -20°C and +40°C.Humidity must be below 95% (no condensation).Never use the product in a humid, dusty environment or where there is a risk of gas or dust explosion.

Yes, this inverter is a Class I safety product and its chassis must be grounded. A grounding point is located outside the product for this purpose. The grounding conductor must have at least half the cross-section of the conductors used for the battery connection.

To fully utilize the inverter’s capacity, it is crucial to use:

Batteries with sufficient capacity. Battery cables with an adequate cross-section to minimize losses and ensure good current flow. For a 5000VA inverter, large cable cross-sections (often exceeding 50 mm²) are required.It is also recommended to install an additional DC fuse or circuit breaker near the battery, especially if the cable length exceeds 1.5 meters.

The inverter does not have an internal fuse on the AC output. The AC wiring is protected by a fast current limiter in case of a short circuit and by an overload detection mechanism. However, it is essential to size your AC wiring correctly based on the inverter's rated power to ensure the safety of the installation.

The inverter uses screw terminals for battery connection. This allows for easy installation without requiring special tools, while ensuring a robust and secure connection.