Kompakta automātiskā stūres sistēma Compact Reactor 40 hidrauliskā ar GHC 50

The Compact Reactor™ 40 autopilot kit for hydraulic systems with the GHC™ 50 instrument pack includes the following main components:

A course computer unit (CCU)An electronic control unit (ECU)A hydraulic pumpAn autopilot instrument GHC™ 50The necessary connection cables between the main componentsNMEA 2000 T-connectors for the networkMounting hardware (screws, nuts, template)An audible alarmPlease note that the Shadow Drive™ sensor is an optional item and may not be included in all packs.

This autopilot is specifically designed for single outboard-powered boats, typically under 25 feet (though some sources indicate up to 30 feet), equipped with hydraulic steering systems.

The 9-axis solid-state AHRS (Attitude Heading Reference System) is designed to minimize heading error, course deviation, and rudder movements. It also helps optimize the system's power consumption.

Garmin’s Shadow Drive™ technology is an optional feature that automatically disengages the autopilot when you take manual control of the helm for a maneuver. Once the heading is stabilized, the autopilot reactivates automatically.

The dimensions of the GHC™ 50 instrument without the sun cover are 105 mm (height) x 140 mm (width) x 51 mm (depth).

The GHC™ 50 instrument is rated IPX7 in accordance with IEC 60529. This means it can withstand accidental immersion in water up to 1 meter deep for a maximum of 30 minutes.

The operating temperature range of the GHC™ 50 instrument is from -15°C to 55°C (i.e., from 5°F to 131°F).

Yes, it is strongly recommended that the autopilot system be installed by a qualified marine installer. Specific knowledge of marine steering systems and electrical systems is essential for correct installation and to avoid any risk of injury or damage to the boat.

For optimal performance, the CCU must be mounted on a rigid surface, in a non-submersible location, near the center of the boat, in any orientation. It is crucial to position it away from sources of magnetic interference such as iron, magnets, high-current wires, and intermittently operating pumps. Ideally, it should be located as close as possible to the boat's center of rotation, on the centerline, lower, and slightly forward.

To test a mounting location for the CCU, use a handheld compass. Hold the compass at the proposed location, then move it 15 cm (6 inches) left, right, up, down, forward, and backward. If the compass needle moves more than three degrees during this test, it indicates the presence of magnetic interference. In this case, you will need to select a new mounting location and repeat the test.

The ECU can be mounted on a flat surface in any orientation. However, it must be located within 0.5 meters (19 inches) of the hydraulic pump. The cables connecting the ECU to the pump cannot be extended. Additionally, the ECU must be installed in a location where it will not be submerged or exposed to splashing.

The hydraulic pump must be mounted in a location where the boat's hydraulic steering lines can be extended. It must be situated within 0.5 meters (19 inches) of the ECU. Ideally, the pump should be mounted horizontally. If vertical mounting is necessary, the hydraulic connections must face upward.

Yes, the CCU cable has a standard length of 5 meters (16 feet). If the CCU cannot be mounted within 5 meters of the ECU, extension cables are available from your Garmin dealer or at garmin.com. Note that this cable must not be cut.

The tools and supplies required for installation include:

Safety glassesDrill and bitsWrenchesJigsaw or rotary cutting tool (for optional tiller pilot installation)Cutting/stripping pliersPhillips and flathead screwdriversCable tiesSolder and waterproof heat-shrink tubing or waterproof crimp connectorsDielectric greaseMarine sealantMarine corrosion inhibitor sprayPortable compass (to test magnetic interference)Hydraulic hoses with field-crimp or field-replaceable fittings (minimum 1000 psi)Hydraulic T-fittingsHydraulic fluidThread sealantHydraulic bleeding kitMounting screws are provided for main components, but you may need different screws if the supplied ones do not suit your mounting surface.

The GHC™ 50 instrument is designed for flush mounting in your boat's dashboard. The mounting surface must be flat, sturdy enough to support the device's weight, and protect it from excessive vibration or shock. The ideal location is at or below eye level for optimal viewing. A template and mounting hardware (wood screws or nut plates and machine screws) are included. It is essential to use only the provided screws for installation to avoid voiding the warranty.

Yes, the system is NMEA 2000® certified, ensuring smooth network communication and the ability to share heading data with other compatible Garmin devices. This integration enables advanced features such as MARPA and chart overlay when the autopilot is connected to a compatible Garmin radar and chartplotter.

The electronic control unit (ECU) must be connected to a 12 to 24 V DC power source. The NMEA 2000 network, which powers the GHC™ 50 instrument and other autopilot components, must be connected to a 9 to 16 V DC power source. The NMEA 2000 power cable must be connected to the boat’s ignition switch or via another inline switch to prevent battery drain.

No, the GHC™ 50 instrument is powered directly from the NMEA 2000 network. Therefore, it does not require a separate power connection.

No, the GHC™ 50 instrument cannot be updated solely via an NMEA 2000 connection. For software updates, it is recommended to use a connection via a Garmin marine network cable (9-pin, sold separately), especially if a compatible Garmin chartplotter is present on the network.

Garmin non-aeronautical products, including this autopilot kit, are warranted against defects in materials or workmanship for a period of one year from the date of purchase. During this period, Garmin will, at its sole discretion, repair or replace any defective component under normal use, free of charge for parts or labor. Shipping costs remain the responsibility of the customer.