Garmin radara antena GMR CHIRP 2106, augšējā daļa

Installing the antenna on the radar pedestal involves a few key steps:

First, remove the protective cover from the waveguide located on top of the pedestal. Next, align the pedestal's waveguide with the socket under the antenna, then slide the antenna onto the pedestal. Secure the antenna to the pedestal by tightening the captive hex bolts located under the antenna arm. Finally, tighten the hex bolts to a torque of 7.9 N·m (6 lbf·ft) to firmly secure the antenna without damaging the equipment. It is recommended to have a marine installer perform this procedure.

When installing the GMR CHIRP 2106 radar, it is crucial to follow these safety instructions:

The radar transmits electromagnetic energy. Ensure the radar beam path is clear of all personnel before transmission.Do not look directly at the antenna up close while the radar is transmitting, as the eyes are the most sensitive part of the body to electromagnetic energy.Do not remove the inline fuse holder when connecting the power cable; the correct fuse must be in place to prevent fire or overheating risks.Installation should be performed by a qualified marine technician to avoid potential injury, damage to the device, or damage to the vessel.Do not attempt to open the device yourself, as it contains no user-serviceable parts and doing so will void the warranty.Always wear safety glasses, hearing protection, and a dust mask when drilling, cutting, or sanding.

The Garmin GMR CHIRP 2106 radar antenna, top section (SKU: 010-01366-00), is the essential radiating component of an open-array Garmin Fantom radar system. Designed to optimize marine detection, it is integral to the radar's offshore performance. This part is specifically the upper element that mounts onto the pedestal (not included with this "top section") and is responsible for transmitting and receiving CHIRP radar signals.

The GMR CHIRP 2106 radar antenna is a component of the Garmin Fantom™ open-array radar series. It is designed to integrate and operate with the radar pedestals in this range, ensuring optimal performance within the Fantom marine network.

The radar, and the voltage converter if applicable, must be connected to a proper water ground. To do this:

Use a 3.31 mm² (12 AWG) copper wire, not included.Connect one end of this wire to the ground connector on the radar pedestal.Apply marine sealant to the ground screw and crimp connector to ensure waterproofing.Connect the other end of the wire to a water ground location on your vessel. It is important to note that this wire must not be connected to the negative terminal of the battery.

Yes, opening the device by anyone other than a technician authorized by Garmin may result in personal injury and/or damage to the device. Furthermore, any damage resulting from unauthorized opening of the unit by a person not approved by Garmin will not be covered under the Garmin warranty. The device contains no user-serviceable parts.

The choice of mounting location is crucial for performance and safety. Here are the main considerations:

The radar must be mounted out of reach of people, with the vertical beam width above head height. It must be mounted high above the vessel's keel line, with minimal obstruction of the radar beam to avoid blind sectors or false echoes. The higher the position, the greater the detection range.The mounting surface must be flat, parallel to the vessel's waterline, and sufficiently robust to support the radar's weight.The location must allow connection to the power supply, ground, and network.The radar must be mounted away from heat sources (exhausts, lights) and at a different level from spreaders and mast crossmembers.Avoid mounting the radar too close to a magnetic compass (respect the specified safety distance).Other electronic equipment and cables must be more than 2 m (6.5 ft) from the radar beam path.GPS antennas must be either above or below the radar beam path.The radar must be mounted at least 1 m (40 in) from any transmitting equipment and cables carrying radio signals (VHF).A minimum distance of 2 m (6.5 ft) is required from SSB radios (single sideband).

The GMR CHIRP 2106 radar antenna is the 'top section' or radiating element of a Garmin Fantom Open Array radar system. It is a key component for target detection and radar beam transmission, thus contributing to navigation and safety at sea.

Radar transmits electromagnetic energy. To prevent bodily injury, damage to the vessel or equipment, or poor product performance, it is imperative that the radar is installed according to the recommendations and that all personnel are kept clear of the radar beam path before transmission.

It is also crucial not to look directly at the antenna up close while the radar is transmitting, as the eyes are the most sensitive part of the body to electromagnetic energy.

This antenna is part of the Garmin Fantom Open Array range. It is designed for seamless integration into the Fantom marine network. For optimal compatibility, it is recommended to use it with a compatible Garmin chartplotter and ensure all Garmin devices on board are running the latest software version.

For the radar antenna installation, you will need the following tools:

A Phillips screwdriver size #2A 6 mm hex keyA drillA 15 mm (19/32 in) drill bitA 32 mm (1 1/4 in) drill bit (optional for cable routing)A 17 mm (21/32 in) wrench and a torque wrench12 AWG (3.31 mm²) bare copper wire for grounding the radar housing and power converter (if applicable)Marine sealant

When choosing the mounting location, consider the following points:

The radar must be mounted out of reach of people, with the vertical beam width above head height. It must be mounted high above the vessel's keel line with minimal obstruction of the radar beam. The mounting surface must be flat, parallel to the vessel's waterline, and sufficiently robust to support the radar's weight. The location must allow connection to power, ground, and the network. Avoid mounting the radar near heat sources, horizontal spreaders, masthead bars, a magnetic compass (observe the safety distance specified by Garmin), or other transmitting equipment.

Once the pedestal is securely mounted, install the antenna in several steps:

Remove the protective cover from the waveguide on top of the pedestal.Align the pedestal's waveguide with the socket under the antenna, then slide the antenna onto the pedestal.Secure the antenna to the pedestal by tightening the captive hex bolts located under the antenna's arm.Tighten the hex bolts to a torque of 7.9 N-m (6 lbf-ft) to secure the antenna without damaging the antenna or mounting hardware.

Yes, to achieve the best possible performance and avoid potential injury or damage to the device or the vessel, installation by a qualified marine installer is recommended by Garmin.

The connection to the power supply depends on whether your model comes with a voltage converter or not. If a voltage converter is included, it must be installed and connected to the boat's battery via a 30 A fuse holder. The radar's power cable already includes a 15 A fuse, and both fuses must be in place. The voltage converter requires an input voltage of 10 to 32 Vdc.

It is recommended to connect the power cable as close as possible to the battery source. The ground cable (not included) must be connected to a water ground, not to the battery's negative terminal.

The radar (and the voltage converter, if applicable) must be connected to an appropriate water ground using a 3.31 mm² (12 AWG) copper wire. This wire is not included with the antenna. It is important to connect the wire to the ground connector on the pedestal and to coat the ground screw and crimp connector with marine sealant.

No, it is imperative not to reuse voltage converters from previous Garmin radar models or third-party converters. Using any converter other than the one included with the radar, or the correct converter purchased from Garmin or your local Garmin dealer, may damage the radar or prevent it from powering on.

You can check your radar's software version on a compatible chartplotter under « Settings > Communications > Marine Network ». To update the software, if your chartplotter has an SD card reader, you can use an SD card (up to 32 GB, formatted as FAT32). If your chartplotter supports Wi-Fi, you can use the ActiveCaptain™ app to download and install software updates.

Yes, opening the device may cause personal injury and/or damage to the device. This device contains no user-serviceable parts and should only be opened by a Garmin authorized service technician. Any damage resulting from opening the unit by someone other than a Garmin authorized service technician will not be covered under the Garmin warranty.

Yes, power cable connection without the appropriate fuse in place voids the product warranty. It is critical to ensure the inline fuse holder is not removed and that the correct fuses (15 A for radar cable and 30 A for voltage converter, if applicable) are installed.