Triton² ātruma/dziļuma/vēja bezvadu komplekts

This pack is a complete instrumentation solution. It includes the following:

A Triton² color displayA WS320 wireless wind sensor interfaceA WS320 wind sensor (vane anemometer)A DST810 smart transducer (depth, speed, temperature)A NMEA 2000 network starter kit (Micro-C backbone)

Yes, the WS320 wind transducer is fully wireless. It communicates via Bluetooth with its interface connected to the NMEA 2000 network. Power is supplied by an integrated solar panel that recharges an internal battery, eliminating the need to run a power or data cable through the mast.

The Triton² display features a 4.1-inch color screen with a resolution of 320 x 240 pixels. It is designed for perfect readability even in full sunlight thanks to its transflective LCD technology and optical bonding that prevents condensation.

The DST810 through-hull smart transducer is a three-function sensor. It measures three essential types of data:

Water depthWater speed (surface speed)Water temperature

Yes, this pack is fully based on the NMEA 2000 standard. It can integrate seamlessly into an existing NMEA 2000 network. The included Micro-C backbone kit also allows you to build the foundation of a new network if you do not have one.

The WS320 wind sensor provides very high precision, validated by wind-tunnel tests. Wind speed accuracy is +/- 0.1 m/s and wind angle accuracy is less than 1 degree.

Yes, the Triton² display can serve as a control screen for a B&G autopilot connected to the same NMEA 2000 network. For full control, it must be paired with a Triton² autopilot keypad.

The main advantage is simplified installation. Not having to run a cable along the mast is not only easier and faster, but also eliminates a potential failure point (cable wear) and preserves the mast's watertight integrity.

The WS320 wind sensor uses a low-power Bluetooth connection to communicate with its interface. The range of this connection is 30 meters, which is more than sufficient for most sailboats.

Yes, the Triton² display has an IPX7 waterproof rating. This means it is protected against temporary immersion in water (up to 1 meter deep for 30 minutes).

The sensors in this pack provide excellent responsiveness:

The WS320 wind sensor transmits data 5 times per second (5 Hz). The DST810 transducer updates speed 5 times per second (5 Hz) and depth once per second (1 Hz).

The DST810 transducer included in this pack can measure depths up to 100 meters (approximately 330 feet).

Yes, the DST810 is a thru-hull transducer model. Installation requires drilling the boat's hull to ensure direct contact with water for depth, speed, and temperature measurements.

Yes, if you have an AIS receiver or transponder connected to your NMEA 2000 network, the Triton² display can show AIS targets on a dedicated page, helping you visualize surrounding traffic.

SailSteer is an exclusive B&G display function available on the Triton² screen. It consolidates all critical sailing data for a sailboat on a single intuitive page: heading, wind, laylines, current, course over ground, etc. This enables faster and more informed decision-making.

The Triton² display is very energy-efficient. Its power consumption is 1.35 W (100 mA) with the backlight off, and 2.16 W (160 mA) with the backlight set to maximum.

Yes, the Micro-C backbone kit includes all basic components (cables, T-connectors, end caps, power cable) to build a small NMEA 2000 network and connect all elements in the pack together.

Yes, you can easily add more Triton² displays to your NMEA 2000 network. Each display will then show data from the sensor pack, allowing you to access the information in multiple locations on your boat (helm station, chart table, etc.).

The Triton² display is designed to withstand demanding marine conditions. Its operating temperature range is from -25°C to +65°C.

The WS320 masthead wind sensor communicates wirelessly via Bluetooth with an interface. This interface, included in the kit, plugs directly into your NMEA 2000 network. It is responsible for transmitting wind data to the Triton² display and any other compatible device on the network.