MultiPlus C 12/1200/50-16

The Victron Energy MultiPlus C 12/1200/50-16 is an integrated and compact power solution combining three essential functions:

A pure sine wave inverter that converts direct current (DC) from batteries into alternating current (AC).

An advanced adaptive battery charger to recharge batteries from an AC source (mains or generator).

An ultra-fast AC transfer switch ensuring uninterrupted power supply in case of power failure.

It is designed for intelligent energy management in marine, mobile, or off-grid applications.

The MultiPlus C 12/1200/50-16 inverter provides a continuous output power of 1200 VA, which corresponds to 1000 W at a temperature of 25°C. It can also supply a peak power of up to 2400 W to start devices requiring high inrush current.

Yes, the MultiPlus C 12/1200/50-16 includes UPS (Uninterruptible Power Supply) functionality. In the event of an AC source failure (mains or generator), it automatically switches to inverter mode in less than 20 milliseconds. This transition is so fast that it does not disrupt the operation of computers and other sensitive electronic devices.

The PowerAssist function allows the MultiPlus to supplement the capacity of a limited AC source, such as a generator or shore power connection. If power consumption exceeds the AC source's capacity, the MultiPlus instantly draws the required energy from the battery to prevent overload. When demand decreases, any excess power is used to recharge the battery. This enables the use of high-power appliances even with a low-amp AC source and potentially allows for a smaller generator to be installed.

The MultiPlus C 12/1200/50-16 uses a 4-stage adaptive charging algorithm controlled by a microprocessor:

Bulk (bulk charge): Charges the battery with maximum current.Absorption: Maintains a constant voltage for full charge, with a duration adapted to the previous discharge.Float (float charge): Maintains the battery at a float voltage to compensate for self-discharge.Storage: Reduces float voltage after 24 hours without discharge to minimize gassing and aging, with weekly equalization. A battery temperature sensor is included to optimize charging voltage.

Yes, the MultiPlus C 12/1200/50-16 is highly suitable for solar energy applications. It can be used in both standalone systems and grid-connected systems. It can use excess solar energy to recharge batteries, and in the event of a grid failure, it can replace the grid to power essential equipment.

Yes, the inverter in the MultiPlus C 12/1200/50-16 can provide a peak power of 2400 W. This capability is particularly useful for starting devices with high inrush current at startup, such as certain motors, pumps, or power tools, without overloading the system.

The PowerControl function limits the maximum AC current that the MultiPlus can draw from an external source, such as a dockside power outlet or a generator. This is useful for preventing overload on these limited sources. The MultiPlus takes into account other energy consumers and uses only the 'excess' current for battery charging, thereby optimizing the use of available power.

Yes, the MultiPlus C 12/1200/50-16 can be compatible with lithium-ion batteries. It is equipped with programmable analog/digital input/output ports that can be used for communication with the battery management system (BMS) of a lithium-ion battery. This enables optimized and secure charge and discharge management for this type of battery.

The MultiPlus C 12/1200/50-16 prevents overloads from limited AC sources (such as a generator or shore power connection) using its PowerAssist function. If power demand exceeds the AC source's capacity, the MultiPlus automatically draws additional energy from the battery. This prevents tripping and allows high-consumption appliances to run even with restricted AC power.

When installing the MultiPlus, it is crucial to follow these safety instructions:

Always disconnect AC power and the battery before any intervention. The product is a Class I device and must be continuously grounded. Ensure adequate ventilation around the product and do not block ventilation openings. Install the product in a heat-resistant environment, away from flammable chemicals, plastics, or textiles. Verify that the available voltage source matches the product's configuration settings.

Yes, the MultiPlus C 12/1200/50-16 is a Class I safety appliance. Its AC input and/or output terminals must be provided with an uninterrupted ground connection for safety reasons. An additional grounding point is also located outside the product to facilitate this connection.

To ensure optimal ventilation, it is essential to leave sufficient free space around the MultiPlus. The ventilation openings must never be blocked. Install the product in a heat-resistant environment and ensure there are no chemicals, plastic parts, curtains, or other flammable textiles in the immediate vicinity of the equipment.

The MultiPlus C 12/1200/50-16 is supplied ready for use, but its settings can be modified in several ways:

The most important settings can be adjusted easily using the DIP switches.All settings (except for the multifunctional relay) can be modified via a VE.Net panel.All settings can be configured using a computer and free software downloadable from the Victron Energy website.

Yes, it is imperative to ensure that the MultiPlus connection cables are equipped with appropriate fuses and circuit breakers. Never replace a protective device with a component of a different type. The product manual provides information on the correct parts to use to ensure the safety and proper operation of the installation.

Yes, it is possible to configure three units of the MultiPlus C 12/1200/50-16 to create a three-phase output. This feature allows the system to adapt to installations requiring a three-phase power supply.

The adaptive battery management system of the MultiPlus C 12/1200/50-16, microprocessor-controlled, can be adjusted for compatibility with various battery types. The adaptive algorithm automatically adjusts to battery usage, optimizing charging for lead-acid batteries (gel, AGM, flooded) and potentially other types such as lithium-ion via programmable ports and external BMS.