MultiPlus C 12/1200/50-16

The Victron Energy MultiPlus C 12/1200/50-16 is an integrated and compact power solution combining three essential functions:

A pure sine wave inverter that converts direct current (DC) from batteries into alternating current (AC).An advanced adaptive battery charger to recharge batteries from an AC source (mains or generator).An ultra-fast AC transfer switch that ensures uninterrupted power in the event of a power outage.It is designed for intelligent energy management in marine, mobile, or off-grid applications.

The MultiPlus C 12/1200/50-16 inverter provides a continuous output power of 1200 VA, which corresponds to 1000 W at a temperature of 25°C. It can also deliver a peak power of up to 2400 W to start devices requiring high inrush current.

Yes, the MultiPlus C 12/1200/50-16 includes a UPS (Uninterruptible Power Supply) function. In case of AC source failure (mains or generator), it automatically switches to inverter mode in less than 20 milliseconds. This transition is so fast that it does not disrupt the operation of computers and other sensitive electronic devices.

The PowerAssist function allows the MultiPlus to supplement the capacity of a limited AC source, such as a generator or shore power connection. If power consumption exceeds the AC source’s capacity, the MultiPlus instantly draws the required energy from the battery to prevent overload. When the load decreases, any excess power is used to recharge the battery. This enables the use of high-power appliances even with a low-ampere AC source and potentially allows for a smaller generator to be installed.

The MultiPlus C 12/1200/50-16 uses a microprocessor-controlled 4-stage adaptive charging algorithm:

Bulk (bulk charge): Charges the battery at maximum current.
Absorption: Maintains a constant voltage for a full charge, with a duration adapted to the previous discharge.
Float (float charge): Keeps the battery at a float voltage to compensate for self-discharge.
Storage: Reduces float voltage after 24 hours without discharge to minimize gassing and aging, with weekly equalization.
A battery temperature sensor is included to optimize charge voltage.

Yes, the MultiPlus C 12/1200/50-16 is extremely well-suited for solar energy applications. It can be used in both standalone systems and grid-connected systems. It can use excess solar energy to recharge batteries, and in case of a grid failure, it can replace the grid to power essential equipment.

Yes, the MultiPlus C 12/1200/50-16 inverter can supply a peak power of 2400 W. This capacity is particularly useful for starting devices with high inrush current at startup, such as certain motors, pumps, or power tools, without overloading the system.

The PowerControl function allows limiting the maximum AC current that the MultiPlus can draw from an external source, such as a shore power outlet or a generator. This is useful to prevent overloading these limited sources. The MultiPlus takes into account other power consumers and only uses the 'excess' current for battery charging, thereby optimizing the use of available power.

Yes, the MultiPlus C 12/1200/50-16 can be compatible with lithium-ion batteries. It is equipped with programmable analog/digital input/output ports that can be used for communication with the battery management system (BMS) of a lithium-ion battery. This allows optimized and secure charge and discharge management for this type of battery.

The MultiPlus C 12/1200/50-16 prevents overloads of limited AC sources (such as a generator or shore power connection) thanks to its PowerAssist function. If power demand exceeds the AC source’s capacity, the MultiPlus automatically draws the additional energy from the battery. This prevents tripping and allows the use of high-power appliances even with restricted AC power.

When installing the MultiPlus, it is critical to follow these safety instructions:

Always disconnect AC power and the battery before any work. The product is a Class I device and must be continuously grounded. Ensure adequate ventilation around the product and do not block the ventilation openings. Install the product in a heat-resistant environment, away from flammable chemicals, plastics, or textiles. Verify that the available voltage source matches the product's configuration settings.

Yes, the MultiPlus C 12/1200/50-16 is a Class I safety device. Its AC input and/or output terminals must be equipped with an uninterrupted ground connection for safety reasons. An additional grounding point is also located outside the product to facilitate this connection.

To ensure optimal ventilation, it is essential to leave sufficient free space around the MultiPlus. Ventilation openings must never be blocked. Install the product in a heat-resistant environment and ensure there are no chemicals, plastic parts, curtains or other flammable textiles in the immediate vicinity of the equipment.

The MultiPlus C 12/1200/50-16 is supplied ready to use, but its parameters can be modified in several ways:

The most important settings can be easily adjusted using the DIP switches. All settings (with the exception of the multifunctional relay) can be modified via a VE.Net panel. All settings can be configured using a computer and free software downloadable from the Victron Energy website.

Yes, it is essential to ensure that the MultiPlus connection cables are fitted with appropriate fuses and circuit breakers. Never replace a protection device with a component of a different type. The product manual provides information on the correct parts to use to ensure the safety and proper operation of the installation.

Yes, it is possible to configure three units of the MultiPlus C 12/1200/50-16 to create a three-phase output. This feature allows the system to adapt to installations requiring three-phase power.

The adaptive battery management system of the MultiPlus C 12/1200/50-16, microprocessor-controlled, can be configured to be compatible with various battery types. The adaptive algorithm automatically adjusts to battery usage, optimizing charging for lead-acid batteries (gel, AGM, flooded) and potentially other types such as lithium-ion via the programmable ports and external BMS.