Omrežni koncentrator OnDeck™

The Garmin OnDeck™ Hub (part number 010-02134-00) is a remote management system designed for boat owners. It allows you to monitor, track, and control various systems on your vessel from anywhere using the ActiveCaptain® mobile app.

This integrated solution provides 3G/4G cellular connectivity for regular updates, ensuring increased peace of mind by enabling remote management of your boat.

The OnDeck™ Hub uses 3G/4G cellular coverage to establish a permanent connection and ensure regular updates of your boat’s data. You interact with the system via the ActiveCaptain® mobile app, available on your smartphone or tablet.

The OnDeck™ Hub monitors essential boat data, such as:

Battery statusBilge pump activityShore power connectionTemperature variationsIt can also support up to 30 safety sensors for extended monitoring.

Yes, the Hub OnDeck™ integrates a GPS receiver that enables position tracking every 15 or 30 minutes, depending on power status. It can also detect movement and send SMS alerts if your boat leaves a geofenced area you have defined.

All data collected by the Hub OnDeck™ is securely stored in the cloud for 30 days, providing a searchable history of your boat's information.

Yes, the Hub OnDeck™ allows remote control of certain systems on your boat via the ActiveCaptain® app. This includes configuring and activating/deactivating digital switches to manage onboard equipment.

The black housing (GTB 10) must be installed in a location that meets the following conditions:

Not exposed to extreme temperatures or conditions.Not submerged.With adequate ventilation.At least 102 mm (4 in) away from cables and other potential sources of interference.With sufficient space for routing and connecting all cables.Connectors must face upward on a horizontal surface or outward on a vertical surface. Do not install with connectors facing down or toward the mounting surface, as the internal GPS antenna will not function properly in this orientation.

After installing the device, you must orient both antennas toward the sky for optimal reception. If the device is mounted on a vertical surface (such as a bulkhead), install the antennas parallel to the black housing. If the device is mounted on a horizontal surface, install the antennas perpendicular to the black housing.

To ensure a watertight connection, tighten the antenna nut to 0.56 N·m (5 lbf·in), which is a hand-tight plus an additional 45-degree turn.

For optimal internal GPS reception, the device must be mounted in a location above the waterline when the boat is in the water and, if possible, have an unobstructed view of the sky.

If you install the device on a boat with a metal hull, or if the internal GPS antenna is blocked or misaligned, you will need to connect an external GPS antenna (sold separately).

The power cable must be connected directly to the battery: the red wire to the positive terminal (+) and the black wire to the negative terminal (-). It is imperative not to remove the integrated fuse holder (7.5 A, 42 V fast-acting).

For correct monitoring of your boat when the ignition is off, the power cable must not be connected to the device via the ignition switch.

When connecting, observe the following points:

Ensure that the power and ground connections to the battery are secure and cannot loosen.Tighten the locking collars so that the power or data connection remains secure.Bare wire connections must be watertight if exposed to moisture (use heat-shrink crimp connectors or other watertight connections).To prevent corrosion of metal contacts, cover unused connectors with protective caps.For a better GPS antenna connection, fully remove the protective cap from the GPS connector.

Yes, the power cable can be extended if necessary, using the appropriate wire gauge for the extension length:

Up to 4.6 m (15 ft): 10 AWG (5.26 mm²) extension wire
Up to 7 m (23 ft): 8 AWG (8.36 mm²) extension wire
Up to 11 m (36 ft): 6 AWG (13.29 mm²) extension wire
A 7.5 A, 42 V fast-acting fuse must remain in place.

Yes, for the initial setup, you must connect your mobile device running the ActiveCaptain® app to the OnDeck system’s Wi-Fi network. If the GTB 10 hub is not connected to a Garmin-compatible chartplotter via the Garmin marine network, these steps must be completed within 30 minutes of powering on the device, as it automatically shuts down after 30 minutes of inactivity.

Yes, the Hub OnDeck™ is designed for native integration with the Garmin ecosystem. It can connect to a compatible Garmin chartplotter via the Garmin Marine Network and to an NMEA 2000 network, enabling monitoring of compatible NMEA 2000 sensors.

The OnDeck™ Hub supports connecting various sensors via its IN/OUT ports, including:

Temperature sensorsSafety sensorsCurrent sensors (shore power)Bilge pump inputs (Bilge 1 and Bilge 2)Battery status inputs (Battery 1 and Battery 2)Boat-in-use inputCan also monitor sensors connected via NMEA 2000 network

Yes, the Boat-in-Use input, bilge pumps (Bilge 1/2), and batteries (Battery 1/2) require a DC voltage between 10 and 32 Vdc.

Yes, OnDeck services require a service plan subscription from Garmin. Each OnDeck product needs its own service plan to operate and access all remote monitoring and control features.

Garmin’s standard limited warranty applies to this accessory. For detailed information and the full warranty terms, you can consult Garmin’s official support and warranty page.

Yes, failure to follow installation instructions may void the product warranty. For example, connecting the power cable without the appropriate fuse in place voids the product warranty.

No, damage caused by extreme temperatures and resulting consequences are not covered by the warranty. The device must be installed in a location not exposed to extreme temperatures and used within the specified temperature range to prevent any damage.