Càmera marina Garmin GC™ 245 amb muntatge pla a coberta, Negre

The Garmin GC™ 245 marine camera is a versatile monitoring solution designed to integrate with Garmin BlueNet™ and Garmin Marine Network navigation systems. It features an adjustable lens module providing wide viewing angle flexibility:

Horizontal rotation of 80 degreesVertical tilt of 62 degreesRoll of 90 degreesThis camera is ideal for various applications, such as deck monitoring, engine room surveillance, or as a stern maneuvering aid. It comes with a GVAM 10 black housing that simplifies connection to the onboard network, including a 2-meter Garmin BlueNet™ cable and a 2-meter power cable.

The GC™ 245 camera is designed for advanced integration with Garmin systems. Here are the connectivity options:

For Garmin BlueNet™ systems: The black GVAM 10 housing includes a 2-metre Garmin BlueNet™ cable that can be directly connected to a BlueNet-compatible GPSMAP® chartplotter or a Garmin BlueNet 20 switch.For existing Garmin Marine Network systems: A Garmin Marine Network adapter cable (part number 010-12531-01), sold separately, is required to connect the GVAM 10 housing to your existing Garmin Marine Network.It is recommended to connect the GVAM 10 housing to the BlueNet side of the network if your boat is equipped with a Garmin BlueNet 30 gateway, for optimal performance and support for future updates.

Yes, the lens module of the GC™ 245 camera is fully adjustable to allow you to fine-tune the orientation after installation. It offers:

A rotation of the camera housing on its base plate up to 80 degrees. A downward tilt of the lens module up to 62 degrees. A roll of the lens module (rotation) up to 90 degrees.

Once the desired viewing angle is confirmed on your chartplotter screen, you must lock the camera in place by tightening the locking ring using the provided Allen key. It is recommended to install the camera with the lens pointing downward at approximately 35 degrees relative to the waterline for an adequate view of objects close to your vessel.

For correct installation of the Garmin GC™ 245 camera, you will need the following tools:

2.8 mm (7/64 in) and 4.5 mm (3/16 in) drill bits suitable for the mounting surface. A 9.5 mm (3/8 in) drill bit if you choose to route the camera cable inside the mounting surface. An 8 mm (5/16 in) SMA torque wrench capable of tightening to 9 kgf-cm (8 lbf-in) for SMA connectors. An 8 mm (5/16 in) wrench to hold one SMA connector while tightening the other. A #2 Phillips screwdriver or bit. 3M™ Marine Adhesive Sealant 5200 or equivalent marine adhesive sealant.

The mounting location is critical for performance and durability:

For the GC™ 245 camera: It must be mounted above the waterline.

For the GVAM 10 black housing: It must be installed in a location that will not be submerged. Ensure adequate ventilation to prevent heat buildup. The housing and its integrated network cable must be mounted at least 71 cm (28 in) away from noisy electrical sources, such as ignition wires and other sensitive electronic devices. Allow sufficient space for cable routing and connections.

It is mandatory to use the cables and connectors provided by Garmin when installing the system. Using cables or connectors other than those provided by Garmin will void the product warranty. The system includes:

An 8-meter (26.25 feet) coaxial cable for the camera. A 2-meter (6.56 feet) Garmin BlueNet™ cable integrated into the GVAM 10 housing. A 2-meter (6.56 feet) power cable integrated into the GVAM 10 housing. It is strongly discouraged to cut, terminate, or splice the provided coaxial cable, as this could cause system malfunction. Failures caused by extended or modified coaxial cables are not covered by the warranty. Longer coaxial cables (25 m, part number 010-13026-02) are available for purchase if needed.

The GC™ 245 camera is compatible with Garmin GPSMAP® chartplotters that support Garmin BlueNet™ or Garmin Marine Network systems. For optimal compatibility and best performance, it is recommended to connect the camera via the Garmin BlueNet™ network if your GPSMAP® chartplotter allows it. If you are using an older GPSMAP® chartplotter on a Garmin Marine Network, an adapter cable (part number 010-12531-01, sold separately) will be required to establish the connection.

The GVAM 10 black box is a key component of the GC™ 245 marine camera system. It performs several essential functions:

Network connectivity: It includes a 2-meter Garmin BlueNet™ cable, allowing easy connection of the camera to your boat's navigation network, whether it's a BlueNet™ system or, with an adapter, a Garmin Marine Network.Power management: It features a 2-meter power cable to supply the camera.Central interface: It acts as an interface between the camera and the GPSMAP® chartplotter, ensuring stable transmission of video data.The GVAM 10 is designed to simplify installation and integration of the camera into your marine electronics system.

The Garmin GC™ 245 marine camera is a versatile monitoring solution designed to integrate with Garmin BlueNet™ and Garmin Marine Network navigation systems. Equipped with an adjustable lens module, it is ideal for applications such as deck monitoring, engine room surveillance, or as a stern maneuvering aid.

The GC™ 245 camera lens module is adjustable, allowing precise adaptation of the viewing angle. It offers 80 degrees of horizontal rotation, 62 degrees of downward vertical tilt, and 90 degrees of roll (clockwise or counterclockwise). A red dot marks the top of the lens.

The black GVAM 10 box is an essential component that facilitates the connection of the GC™ 245 camera to the onboard network. This box includes a 2-meter Garmin BlueNet™ cable and a 2-meter power cable, simplifying the installation of the system.

The GC™ 245 camera is designed for flush deck mounting and must be installed strictly above the waterline. It is recommended to install it in a location not exposed to extreme temperatures or conditions. For an adequate view of objects close to your boat, install the camera with the lens pointing downward at approximately 35 degrees relative to the waterline.

The GVAM 10 black housing must be mounted in a location where it will not be submerged and where it has adequate ventilation to prevent heat buildup. It is also necessary to mount it and route its network cable at least 71 cm (28 inches) away from noisy electrical sources, such as spark plug wires and other sensitive electronic devices.

For installing the GC™ 245 camera, the following tools are required:

A 2.8 mm (7/64 in) drill bit suitable for the camera’s mounting surface. A 4.5 mm (3/16 in) drill bit suitable for the black housing’s mounting surface. A 9.5 mm (3/8 in) drill bit to drill through the camera’s mounting surface for internal cable routing (optional). A torque wrench for 8 mm (5/16 in) SMA connectors, capable of tightening to 9 kgf-cm (8 lbf-in). An 8 mm (5/16 in) wrench to hold the SMA connector. A #2 Phillips screwdriver or bit. Marine adhesive sealant 3M™ Marine Adhesive Sealant 5200 or equivalent.

The GC™ 245 camera’s coaxial cable can be routed in two ways: either through the hull by drilling a 10 mm (3/8 in) cable pass-through hole, or externally along the mounting surface. It is critical not to cut, splice, or join the supplied coaxial cable, as this may cause system malfunction.

It is not recommended to print a mounting template yourself. It is better to use the template provided in the product box. If you must print one, it is crucial to ensure the print scale is set to 100% and that the paper is large enough to avoid incorrect cutting on your boat's mounting surface.

The GVAM 10 black box includes a 2 m (6.56 ft) Garmin BlueNet™ cable and a 2 m (6.56 ft) power cable. The GC™ 245 camera comes with an 8 m (26.25 ft) coaxial cable.

The GC™ 245 camera is compatible with Garmin GPSMAP® chartplotters and can integrate with Garmin BlueNet™ and Garmin Marine Network systems. It is designed to work with Garmin BlueNet devices and Garmin Marine Network devices.

To connect the GC™ 245 camera to an existing Garmin Marine Network system, you must use a Garmin Marine Network adapter cable (part number 010-12531-01), which is sold separately. This cable connects the GVAM 10 unit's integrated Garmin BlueNet™ cable to your Garmin Marine Network chartplotter or a GMS™ 10 port expander.

Yes, it is possible to extend the length of some cables if necessary:

If the black GVAM 10 housing is more than 2 meters from your Garmin BlueNet chartplotter or switch, you can extend the integrated Garmin BlueNet™ network cable by purchasing an additional Garmin BlueNet™ cable and a coupler.If the black housing is more than 2 meters from your power supply, you can extend the power cable.If the camera is more than 8 meters from its black housing, you can use a longer coaxial cable, such as the 25-meter cable (reference 010-13026-02), available from your Garmin dealer or on garmin.com.It is important not to modify the supplied coaxial cables, as this could void the warranty.