Sonda GT17M-THF 0° - transversal CHIRP freqüència mitjana

The Garmin GT17M-THF 0-degree transducer features a stainless steel housing and is compatible with a wide range of hull materials. It can be installed on fiberglass, wood, composite, aluminum, and steel hulls. For aluminum or steel hulls, it is critical to use the included galvanic isolation components to prevent corrosion and potential water ingress.

The deadrise angle is the angle between a horizontal line and the outer hull at a given point. For optimal depth sounder performance, it is essential that the sounder's angle matches the deadrise angle at the installation location as closely as possible.

The Garmin GT17M-THF 0-degree depth sounder is specifically optimized for hulls with a deadrise angle of 0 to 5 degrees. Garmin offers other GT17M-THF models with 12 or 20-degree angles to suit hulls with different deadrise angles. It is recommended to check your hull's deadrise angle before drilling holes.

When installing the GT17M-THF transducer on an aluminum or steel hull, it is imperative to use the included galvanic isolation components. Failure to follow this instruction will result in galvanic corrosion that could cause water infiltration around the transducer and damage the hull. These components are designed to electrically isolate the transducer from the metal hull, thereby preventing the electrochemical reaction.

To install the Garmin GT17M-THF transducer, you will need the following tools:

A drillA 3 mm (1/8 in) drill bitA wrench suitable for nuts up to 108 mm (4 1/4 in)A 4.5 mm (3/16 in) Allen keyMarine sealant (flexible, fast-curing, for below the waterline)Mild household detergent or rubbing alcoholSandpaperMasking tapeWaterproof electrical tapeA 98 mm (3 7/8 in) hole saw for fiberglass hulls (solid or cored)A 101 mm (4 in) hole saw for metal hullsGrommets and water-based antifouling paint may also be required depending on the installation.

For optimal performance, the depth sounder must be installed in an area with clean, non-turbulent water. Here are some general considerations:

General location: The transducer should be mounted forward and near the engine (for outboards/sterndrives) or away from the propeller and propeller shaft (for inboards). Avoid obstacles: Do not install it behind ribs, struts, fittings, water intake or discharge ports, or anything that could create air bubbles or cause turbulent water.Alignment: Mount the transducer parallel to the bow-stern axis of your vessel.Specific hulls: For stepped hulls, install it forward of the first step. For full-keel hulls, mount it slightly angled toward the bow, parallel to the centerline. For fin-keel hulls, 25-75 cm ahead of the keel and a maximum of 10 cm to the side of the centerline.Propellers: On single-propulsion boats, do not mount the transducer in the propeller wash. On twin-propulsion boats, mount it if possible between the propellers.

Yes, it is mandatory to update the software of your Garmin chartplotter when you install this transducer. This ensures compatibility and correct operation between the transducer and your Garmin device. You can find the update instructions in the user manual of your chartplotter.

Preparing a cored-fiberglass hull is critical to prevent water intrusion. Follow these steps:

Drill a 3 mm (1/8 in) pilot hole from the outside of the hull.Apply masking tape around the pilot hole on the outside to reduce gelcoat cracking.Use a 98 mm (3 7/8 in) hole saw to cut the depth sounder hole through the entire hull from the outside.From inside the hull, use a slightly larger hole saw to cut only the inner fiberglass skin and core, ensuring the outer skin remains intact.Seal the core inside the hull using fiberglass resin or casting epoxy. For epoxy, use a 98 mm waxed cylinder as a spacer during curing.Once cured, sand and clean the inside and around the hole.Incorrect core sealing can lead to serious hull damage.

To ensure the longevity and performance of your Garmin GT17M-THF transducer, follow these maintenance guidelines:

Leak check: After launching your boat, always check for leaks around the screw holes or the transducer itself.Operation: The transducer must always be submerged in water to function properly. Using it out of the water can damage it due to overheating.Cleaning: To clean the transducer surface, never use solvents such as mineral spirits, acetone, MEK, or similar products. Do not use an electric sander or a pressure washer.Anti-fouling paint: If necessary, you can apply water-based anti-fouling paint to the transducer to prevent corrosion and fouling. Do not use other types of paint.

The Garmin GT17M-THF transducer features a stainless steel housing, providing high durability and optimal resistance to harsh marine environments.

Mounting hole dimensions depend on your hull material:

For a solid fiberglass hull or a fiberglass hull with a core, a 98 mm (3 7/8 in) hole is required.For a metal hull (aluminum or steel), a 101 mm (4 in) hole is required.These dimensions are critical for proper installation.

Yes, you can apply water-based antifouling paint to the transducer to prevent corrosion and marine growth. It is important to use only water-based antifouling paint and avoid solvents.

The Garmin GT17M-THF transducer is designed to be installed on a wide range of hull materials, including fiberglass, wood, composite, aluminum, and steel.

The Garmin GT17M-THF 0-degree transducer is optimized for hulls with a deadrise angle between 0 and 5 degrees. For different deadrise angles, Garmin offers other GT17M-THF models with 12 or 20-degree angles, allowing precise adaptation to each vessel's geometry.

Yes, when installing the GT17M-THF depth sounder on an aluminum or steel hull, it is mandatory to use the included galvanic isolation components. This feature is critical to prevent galvanic corrosion, which could lead to water ingress around the transducer and damage the hull.

Yes, to ensure optimal performance and avoid any risk of injury, damage to the device, or the vessel, installation by a qualified marine technician is highly recommended.

To avoid permanently damaging the depth sounder’s surface, do not use solvents such as white spirit, acetone, methyl ethyl ketone (MEK), or similar products. Avoid using an electric sander or a high-pressure cleaner for cleaning.

It is important not to mount the transducer behind ribs, frames, fittings, water inlet or outlet openings, or any element likely to create air bubbles or turbulent water. The transducer must be in clean, non-turbulent water for optimal performance. Also avoid installing it near the engine or in the engine room to prevent interference with the sonar signal and overheating risks.

After physically installing the depth sounder, it is crucial to update the Garmin chartplotter software. Detailed instructions for the update are available in your chartplotter's user manual. Additionally, once the boat is in the water, it is recommended to check for any leaks around the transducer before leaving the boat submerged for an extended period.

Yes, it is essential to apply marine sealant along the water path to ensure a watertight seal between the depth sounder and the hull. This includes applying a 4 mm (1/8 in) layer of sealant on the internal flange of the depth sounder and a layer around the depth sounder housing where it will contact the sides of the hole in the hull.

For the installation of the GT17M-THF transducer, you will need the following tools:

A drill with a 3 mm (1/8 in) bitA 98 mm (3 7/8 in) hole saw for fiberglass hulls or a 101 mm (4 in) hole saw for metal hullsA wrench suitable for nuts up to 108 mm (4 1/4 in)A 4.5 mm (3/16 in) Allen keyMarine sealant (flexible, quick-curing type for below the waterline)Mild detergent or rubbing alcohol, sandpaper, masking tape, waterproof electrical tapeOptional grommets and water-based antifouling paint (optional)