Sonda Panoptix LiveScope LVS12

The Panoptix LiveScope LVS12 transducer is designed to connect directly to compatible Garmin chartplotters. Unlike other LiveScope transducers such as the LVS32 or LVS34, which require an external black housing module (GLS10), the LVS12 simplifies installation by integrating directly into your chartplotter.

The Garmin Panoptix LiveScope LVS12 transducer provides LiveScope forward and down views. These views allow real-time visualization of what is happening underwater, ahead and directly below your boat, which is essential for detecting fish and structures.

For optimal performance, several points must be considered when installing the LVS12 transducer:

Do not install the transducer in the propeller wash path. On an outboard motor, install it on the side of the descending propeller flow (usually starboard).Choose a location where it will not be shaken during launching, hauling, or storage.Avoid installing it behind stringers, struts, fittings, water intakes or discharges, other through-hull transducers, or anything that could create air bubbles or cause turbulent water.Install it as close as possible to the boat's centerline.On twin-engine vessels, install it between the engines if possible.

The following tools are typically required for installation:

DrillBits: 4 mm (5/32 in) and 3.2 mm (1/8 in)Masking tapePhillips screwdriver #2Marine sealantHole saw 32 mm (1 1/4 in) (optional)Cable ties (optional)

Yes, the Panoptix LiveScope LVS12 transducer can be installed in several ways. The installation instructions detail the procedures for mounting on the electric motor (on the shaft or directly on the motor) as well as for mounting on the boat's transom. It is important to follow the specific recommendations for each type of installation to ensure optimal performance.

Yes, it is mandatory to update your Garmin chartplotter’s software after installing the Panoptix LiveScope LVS12 transducer. If your chartplotter has Wi-Fi capability, you can perform the update via the ActiveCaptain™ app on a compatible Android™ or Apple device. If your chartplotter does not have Wi-Fi, the update is done using a memory card and a Windows computer.

The dimensions of the Panoptix LiveScope LVS12 transducer are as follows:

Length: 113 mm (4.45 in)Height: 92 mm (3.6 in)Width: 23 mm (0.9 in)

Before calibrating the compass, the transducer must be installed on the shaft far enough from the electric motor to avoid magnetic interference, and deployed in the water. The calibration must be of sufficient quality to activate the internal compass. For best results, using a heading sensor such as the SteadyCast™ is recommended. The general procedure is as follows:

From a suitable sonar view, select MENU > Sonar Settings > Installation. If necessary, select Use AHRS to enable the AHRS sensor. Select Calibrate compass. Follow the on-screen instructions, performing a full 1.5 rotations of the boat during calibration.

The Panoptix LiveScope LVS12 transducer is distinguished by its ability to connect directly to certain compatible Garmin chartplotters without requiring an external black box (sonar module) such as the GLS10. This greatly simplifies installation and wiring. It provides both forward and down LiveScope views.

The LiveScope LVS12 transducer offers two main sonar views:

Forward LiveScope view: Allows real-time viewing of fish and structures ahead of your boat.

Down LiveScope view: Allows real-time viewing of fish and structures directly beneath your boat.

For the installation of the Garmin LVS12 transducer, you will generally need the following tools:

Drill4 mm (5/32 in) and 3.2 mm (1/8 in) drill bitsMasking tapePhillips screwdriver #2Marine sealantHole saw 32 mm (1 1/4 in) (optional)Cable ties (optional)

When installing on an electric motor, it is crucial to:

Secure the transducer cable along the shaft or another safe location to prevent damage.Orient the mounting bracket of the electric motor shaft so that the narrow end of the angle is upward.Position the angled side of the transducer toward the front of the electric motor.Route the cable so that it is not pinched when the motor is deployed or stowed.

Yes, the LVS12 transducer can be installed on the boat's transom using the supplied mounting bracket. It is important to align the transducer's line with the bottom of the transom for correct underwater alignment. For deep-V hulls, an extension bracket can be added to position the transducer lower below the waterline.

Yes, it is mandatory to update your Garmin chartplotter software after installing the LVS12 transducer to ensure compatibility and optimal performance. If your chartplotter supports Wi-Fi technology, the update can be performed via the ActiveCaptain app. Otherwise, a memory card and a Windows computer can be used.

To calibrate the LVS12 sounder's compass, follow these steps:

Ensure the sounder is installed far enough from the engine to avoid magnetic interference and that it is deployed in the water. From a compatible sonar view, select MENU > Sonar Setup > Installation. If needed, select Use AHRS to enable the AHRS sensor. Select Calibrate Compass. Follow the on-screen instructions, rotating your boat 1.5 times during calibration. For best results, using an external heading sensor such as the SteadyCast heading sensor is recommended.

The Panoptix LiveScope LVS12 transducer measures 113 mm (length) x 92 mm (height) x 23 mm (width), or approximately 4.45 x 3.6 x 0.9 inches.

To maintain the performance of your LiveScope LVS12 transducer, it is important to clean it regularly. Aquatic debris can build up quickly and reduce the device's efficiency. To clean it, use a soft cloth and mild detergent, then wipe it dry.

No, the Panoptix LiveScope LVS12 transducer is designed to connect directly to compatible Garmin chartplotters. It does not require an external black housing (sonar module) like the GLS10, which simplifies installation.