Sonda traversant GDT™ 43 (profunditat/temperatura)

The Garmin GDT™ 43 transducer is designed to accurately measure water depth and temperature. It operates at a frequency of 50 kHz and delivers a transmit power of 300 Watts.

The GDT™ 43 transducer can measure depths up to 152 metres (500 feet).

The GDT™ 43 depth sounder is made of plastic, ensuring durability suited to the marine environment.

The GDT™ 43 transducer is compatible with NMEA 2000® networks via a NMEA 2000® adapter (not included) or directly with a NMEA 0183 system.

Yes, the GDT™ 43 transducer is designed to directly replace existing Nexus and Silva 43 mm (TH43) through-hull transducers, making upgrades straightforward.

The GDT™ 43 transducer is compatible with hulls with a deadrise angle of 0 to 20 degrees.

For the installation of the GDT™ 43 transducer, you will need the following tools:

A drillA 43 mm (1 11/16 in) hole sawA 52 to 55 mm (2 1/16 to 2 3/16 in) hole saw for fiberglass sandwich hullsMarine sealantSilicone greaseCable cuttersMetal file (for metal hulls)Fiberglass cloth and resin (optional for sealing a fiberglass sandwich hull)A 43 mm (1 11/16 in) cylinder, wax, tape, and casting epoxy (optional for sealing a fiberglass sandwich hull)

On keel-wing sailboats, the transducer must be mounted more than 25 cm (10 in) and less than 75 cm (30 in) ahead of the keel, and less than 10 cm (4 in) from the centerline.

Yes, for optimal performance, the transducer should not be installed:

Behind strakes, skegs, fittings, through-hulls, or any scuppers or openings that create air bubbles or cause turbulent water flow.
In a location where it could be shaken during launching, towing, or storage.
Near the edge of sharp hull strakes on powerboats.
In the path of the propeller on single-screw vessels.

To prepare a fiberglass sandwich hull, first drill a 3 mm (1/8 in) pilot hole through the hull. Then, from the outside, cut a 43 mm hole through the outer skin only. Inside, cut a 9 to 12 mm larger hole through the inner skin and most of the core, without cutting the outer skin. Remove the cut core and inner skin, sand and clean the area. Finally, seal the core using layers of fiberglass cloth and resin, or with casting epoxy and a spacer sleeve.

It is crucial to properly seal the core of a fiberglass sandwich hull to prevent water from seeping into the core, which could seriously damage the boat.

The GDT™ 43 transducer connects to the NMEA 2000® network via a NMEA 2000® adapter. This adapter must then be connected to a NMEA 2000® T-connector that is part of the network.

No, the NMEA 2000® adapter is not included with the GDT™ 43 transducer and must be purchased separately.

The general installation steps include:

Cut a 43 mm hole in the hull.Insert the through-hull fitting.Apply marine sealant to the outer flange of the fitting and hand-tighten the nut.Slide the O-rings onto the plug and apply silicone grease.Insert the plug into the fitting.Ensure the plug is properly seated.Install the fitting with the pin at 90 degrees to the boat's centerline.After the sealant has cured, remove the nut, apply sealant inside the hull, then reinstall and hand-tighten the nut.Replace the plug with the actual transducer.Install the wire locking device on the transducer.

It is recommended to keep the cap for use during cleaning or maintenance of your transducer.

Yes, the retractable design of the transducer minimizes fouling. Additionally, the supplied plug can be used when cleaning or servicing your transducer.

You must use a 43 mm (1 11/16 in) hole saw to drill the hole in the hull. For sandwich fiberglass hulls, a 52 to 55 mm (2 1/16 to 2 3/16 in) hole saw is also required to prepare the core.

An NMEA 2000 drop cable, used to connect a device to the main backbone network, is limited to a maximum length of 6 meters (20 feet).

NMEA 2000 devices must operate with a 9 to 16 V DC power supply, with a nominal voltage of 12 V DC.

To ensure optimal performance of your Garmin GDT™ 43 through-hull transducer, it is essential to choose an appropriate mounting location. Here are the key considerations based on your vessel type and general best practices:

On fin-keel sailboats: The transducer must be mounted more than 25 cm (10 in) and less than 75 cm (30 in) forward of the keel, and within 10 cm (4 in) of the centerline.On full-keel sailboats: The transducer must be mounted at a slight angle toward the bow, not parallel to the centerline.On planing powerboats and vee-bottom hulls: Avoid mounting the transducer near the sharp chines of the hull.On single-screw vessels: The transducer must not be mounted in the propeller wash path.On twin-screw vessels: If possible, mount the transducer between the two propellers.Generally, for all vessel types:

The transducer must be mounted parallel to the fore-aft axis of your vessel.Choose a location that allows easy access to the transducer from inside the vessel.Avoid mounting the transducer behind chines, stiffeners, fittings, water discharge outlets, or any element likely to create air bubbles or turbulence. The transducer must always be in smooth (non-turbulent) water for optimal performance.Do not mount the transducer where it could be struck during launching, beaching, or storage.Be aware that the transducer may cause cavitation, which can degrade vessel performance and damage the propeller.