Capteur Trifonctions Sondeur/Loch et Température

Free pickup point shipping over €150 in France
Pickup at Skysat possible

Custom installation

Trust Skysat to install the equipment on board

Request a quote

Installers near you

thanks to our network of approved installers

Find an installer

Support service

Opt for additional installation assistance

Save 13%

Raymarine

T910

Triducer Depth Sounder/Speed Log and Temperature Sensor

The Raymarine T910 is a hull transmitter designed to process depth, speed, and temperature data from a triducer, integrating with the boat’s 12/24Vdc system. This unit is essential for centralizing and transmitting navigation data. Includes: self-tapping screws and mounting template.

Retail priceBenefit from the professional rate

217,46€

217,46€ ~~252,00€~~

Tax included. Shipping calculated at checkout.

In stock

Free pickup point shipping over €150 in France
Pickup at Skysat possible

Custom installation

Trust Skysat to install the equipment on board

Request a quote

Installers near you

thanks to our network of approved installers

Find an installer

Support service

Opt for additional installation assistance

Technical specifications

Operating voltage	12/24 V
Product width	47 mm
Product height	52.5 mm
Product depth	42.5
Bus compatibility	NMEA 2000
Wired network	NMEA 2000
Mounting type	Surface mount
Self-closing valve	No
Flush mount	No
Installation location	Inside, above the waterline, ventilated
Boat speed calibration	Via connected navigation system
Temperature measurement	Yes
Sensor output type	Digital (NMEA 2000)
Sensor type	Multifunction sensor interface

Detailed description

The Raymarine T910 is a hull-mounted transducer interface designed to process data from a triducer (triple-function sensor) measuring depth, speed, and temperature. This unit acts as an intermediary between the triducer and the vessel’s navigation system, consolidating these three critical parameters for accurate monitoring. It supports 12/24Vdc shipboard power and can also be powered by a Raymarine solar panel if no dedicated power source is available.

T910 Installation and Connectivity

Installing the Raymarine T910 requires strategic placement aboard the vessel. The unit must be mounted vertically, with cables exiting from the bottom, and positioned at least 50 cm above the waterline. Direct contact with water must be avoided, and a well-ventilated area is required—avoid sealed watertight compartments. Mounting is done using three 2.5 mm holes, with self-tapping screws provided. Care must be taken not to overtighten to prevent damage to the housing.

Wiring and Integration Details

Connecting the triducer cables to the Raymarine T910 follows a specific color code. For a triducer, the ground shield must be connected to the depth connector, not the speed connector, to prevent short circuits. If the speed sensor lacks an integrated temperature probe, the brown and white wires of the speed connector must be linked to ensure signal continuity. Applying silicone grease to the terminals is recommended to optimize the connection, and cable support near the transmitter is advised. Finally, the cover must be correctly positioned to keep the outer cable sheaths inside the transmitter, ensuring adequate protection for the entire wiring system.

Documentation

Type	Nom
	EN - Mounting Template - Trifunction Sensor Fishfinder/Speed and Temperature
	EN - Installation Manual - Triducer Fishfinder/Speed & Temperature Sensor
	EN - User Manual - TriFunction Depth Sounder/Speed Log and Temperature Sensor
	EN - User Manual - Triducer Fishfinder/Speed & Temperature Sensor
	EN - User Manual - Triducer Fishfinder/Speed & Temperature Sensor
	EN - User Manual - Triducer Depth Sounder/Speed & Temperature Sensor
	EN - User Manual - Trifunction Sensor Fishfinder/Speed Log and Temperature

Expert opinion

Pol CONIN

Digital Manager

« Raymarine T910 interface: reliable management of triducer data »

The Raymarine T910 is an essential hull-mounted transmitter for vessels requiring reliable centralization of core navigation data: depth, speed, and temperature. This module is not the sensor itself but the electronic interface that receives and processes signals from an external triducer. Its practical value lies in converting raw sensor data into usable information for the onboard electronic system, often for integration into an NMEA or SeaTalkNG network, with NMEA output protocol specifically mentioned in the technical documentation.

Installing the T910 requires consideration. As a hull-mounted transmitter, it is installed inside the vessel, simplifying maintenance and avoiding additional hull penetrations compared to a through-hull transducer. However, this imposes specific constraints: vertical mounting, more than 50 cm above the waterline, and in a ventilated space away from direct moisture. These requirements are critical to ensure longevity and signal reliability. Installers must pay close attention to transducer wiring, particularly grounding the shield to the depth connector for triducers, and bridging the brown and white terminals if the speed sensor does not include a temperature probe. These details are decisive for proper operation and system integrity.

This type of interface is particularly relevant for owners looking to modernize or improve navigation data acquisition without replacing all their sensors. It serves as a key component for converting and transmitting basic data, often a prerequisite for display on multifunction instruments or dedicated screens. It is not suitable for direct exposure to the elements or installation in sealed compartments that would prevent necessary ventilation.

Durabilité

Facilité d'installation

Rapport performance / prix

Payment and security

Your payment information and data are processed securely.

Triducer Depth Sounder/Speed Log and Temperature Sensor

217,46€

217,46€ ~~252,00€~~

Frequently Asked Questions

Need help? Contact us

What are the prerequisites for drilling the mounting holes for the T910?

You must drill three 2.5 mm holes. These holes are marked "B" on the mounting template provided with the device.

Which screws should be used to mount the T910 and are there any precautions?

The T910 must be mounted using the provided self-tapping screws. It is critical not to overtighten the screws, as this could damage the housing molding.

How to connect the transducer cables to the Raymarine T910?

Connect the transducer cables to the Raymarine T910 following the color code indicated on the unit. It is also necessary to sleeve the shields to prevent short circuits.

How to connect the ground braid of a triducer to the T910?

For a triducer, the ground braid MUST be connected to the depth connector, not the speed connector. This prevents short circuits and ensures proper operation.

What to do if my speed sensor has no integrated temperature probe?

If your speed sensor does not include a temperature probe, you must connect the brown and white wires of the speed connector. This connection ensures signal continuity.

Should a product be applied to the T910 connection terminals?

Yes, it is recommended to apply silicone grease to the connection terminals to optimize connection quality and protect it.

How to ensure proper cable management after connection to the T910?

It is recommended to support the cables near the transmitter. Additionally, the unit's cover must be correctly positioned to keep the outer cable sheaths inside the transmitter, ensuring their secure attachment and protection.

How to check that the T910 cover is correctly installed?

Ensure the cover is properly seated and that it secures the outer sleeves of the cables inside the transmitter housing. This ensures protection of the connections and the durability of the installation.

Is the T910 compatible with all types of transducers?

The Raymarine T910 is specifically designed to be used with a triducer (triple-function transducer) measuring depth, speed, and temperature. Its compatibility will therefore depend on the type of triducer you have.

Can the T910 be used with older transducers?

Yes, the T910 can potentially be used with older transducers. However, it is advisable to carefully check the connections, especially if the speed sensor does not have an integrated temperature probe, in which case a link between the brown and white terminals of the speed connector will be required.

What types of data can the T910 process?

The T910 is designed to process and interface depth, speed (log), and temperature data. These three types of measurements are consolidated by the unit for your navigation system.

Can incorrect installation of the T910 void the warranty?

Yes, failure to follow the installation instructions provided with the Raymarine T910 may void your warranty. It is therefore essential to strictly adhere to all guidelines for installation and wiring.