Lynx 1000 DC M8 distribution block

The Lynx 1000 DC M8 distributor is a key component of Victron Energy’s modular Lynx busbar system. It integrates a positive busbar and a negative busbar. The positive section provides four connections protected by MEGA fuses (to be purchased separately) with a fuse status monitoring function. The negative section has four connections and one ground connection, all with M8 terminals.

The Lynx distributor provides four positive connections protected by fuses and four negative connections. It also features a separate ground connection.

The Lynx M8 fuse block is designed to accept MEGA-type fuses. These fuses must be purchased separately as they are not included with the fuse block.

No, the Lynx fuse block is designed to accept MEGA fuses, but these must be purchased separately and are not included with the module.

The Lynx distributor comes with a 40 cm RJ10 cable. This cable is used to power the Lynx distributor and also to transmit data, including fuse status, when connected to a Lynx Smart BMS.

The Lynx distributor has four LEDs indicating the status of the fuses, one for each positive connection. It monitors each fuse and will detect if a fuse is blown, signaling the status via these LEDs.

The M8 or M10 designation refers to the busbar connection joints where Lynx modules are interconnected. The specific product, the Lynx 1000 DC M8 Power Distribution Unit, uses M8 busbar connections. The fuses and cable connections on this distribution unit are also always M8.

Yes, the Lynx distributor's negative bus bar has a dedicated ground connection, in addition to the four standard negative connections.

The Lynx distributor is part of a DC distribution system that typically supports system voltages of 12 V, 24 V or 48 V. The battery voltage range supported by associated components such as the Lynx Smart BMS is 9 to 60 VDC.

The Lynx distribution block is an essential solution for protecting and managing DC circuits within the Lynx modular distribution system. It allows distributing DC power to multiple devices while individually protecting each circuit with fuses and monitoring their status.

Yes, the Lynx distributor is fully compatible with the Lynx Smart BMS. When connected to a Lynx Smart BMS, up to four Lynx distributors can send information about their fuse status to the BMS. This data is then accessible via the VictronConnect app or a GX device.

Yes, if the Lynx distributor is connected to a Lynx Smart BMS, you can monitor the status of its fuses via a GX device (such as a Cerbo GX). This allows local or remote monitoring via the VRM portal.

Yes, if the Lynx distributor is connected to a Lynx Smart BMS, it can be monitored and configured using the VictronConnect app on your smartphone or tablet.

No, the fuse status monitoring feature of the Lynx distribution panel is not available if the panel is connected to a Lynx Shunt VE.Can. This feature is specifically enabled when connected to a Lynx Smart BMS.

Up to four Lynx distributors can be connected to a Lynx Smart BMS to send data on the status of their fuses and enable monitoring.

Yes, the Lynx distributor can be used alone to provide a fused DC distribution. However, to benefit from advanced fuse monitoring via the VictronConnect app or a GX device, it must be connected to a Lynx Smart BMS.

Before working on the Lynx distribution system, it is essential to ensure the busbars are not live. Disconnect all battery positive poles before removing the Lynx front cover. Only qualified technicians should work on batteries, following the safety warnings in the battery manual.

The Lynx modules are designed to be mechanically interconnected via their busbars. They can be mounted side by side to form a compact and modular distribution system. The Lynx M8 distributor uses M8 busbar connection joints for this interconnection.

To connect the DC cables to the Lynx distributor:

The positive cables are connected to the four fused positive terminals. The negative cables are connected to the four negative terminals. A dedicated ground connection is also available. All these connections use M8 terminals.

The Victron Energy Lynx 1000 DC M8 distributor is a key component of the Lynx modular busbar system, designed for DC electrical distribution.

It includes a positive busbar and a negative busbar:

The positive busbar has four connections protected by MEGA fuses (sold separately). These connections include a fuse status monitoring feature.The negative busbar provides four connections for equipment and one ground connection.This module comes with a 40 cm RJ10 cable, which powers it and transmits data. When connected to a Lynx Smart BMS, the distributor can send information about the status of its fuses. This data can be accessed via the VictronConnect app or a GX device (such as a Cerbo GX), enabling local or remote monitoring via the VRM portal. Note that this monitoring feature is not available if the distributor is connected to a Lynx Shunt VE.Can.

The Lynx distribution system, of which this distributor is part, is designed for a nominal capacity of 1000 A. This specific model uses M8 connections for fuses and cables.