Supersub 500 Bilge Pump - 12 V

No, the mounting bracket is provided only with the automatic pumps in the Supersub range. Since the SS5012 pump is a standard model, it does not include this accessory.

The Whale Supersub 500 (SS5012) bilge pump is a standard model. This means it has no built-in automatic function and requires a separate bilge switch for operation.

No, the Whale Supersub 500 (SS5012) bilge pump is not specified as being supplied with an integrated non-return valve (N.R.V.). The product documentation indicates that some other models in the Supersub range may include one, but this is not the case for the SS5012 model.

The Whale Supersub 500 bilge pump, part number SS5012, operates at 12 Volts direct current (d.c.).

The Whale Supersub 500 bilge pump (reference SS5012) belongs to the "Supersub / Orca Auto 1300" range. It is always recommended to verify the exact reference and compatibility with existing onboard equipment before purchasing and installing.

The Whale Supersub 500 - 12 V bilge pump, part number SS5012, is specifically designed for electric bilge pumping on boats. It is part of the Supersub range, known for its low-profile and narrow electric bilge pumps.

The Whale Supersub 500 - 12 V bilge pump (reference SS5012) is specifically designed for the rapid and efficient evacuation of bilge water from recreational boats. Its low and narrow profile allows installation in confined spaces that other bilge pumps could not access.

No, the Supersub 500 bilge pump (model SS5012) is not an automatic pump. It requires a separate bilge switch for manual activation. For automatic operation, an electronic switch or external float switch must be used as an additional component.

The Whale Supersub 500 bilge pump operates on 12 V direct current (DC) power.

The Supersub range is designed to pump only normal bilge water from recreational boats. It is the user's responsibility to ensure material compatibility if the product is intended for use with another liquid.

No, it is important to stop the pump as soon as the water has been evacuated from the bilge. Running the pump dry will reduce its lifespan.

The pump must be mounted on a surface with a minimum thickness of 19 mm (3/4"). It is important not to screw it directly to the hull, but rather to a bulkhead or an additional board. The pumped water must be discharged via a through-hull fitting installed above the boat's waterline.

Yes, a check valve (part number LV1219) is recommended for SS5012 models to optimize pump performance.

Yes, the wiring must comply with applicable electrical standards and include a properly rated fuse or circuit breaker. Power must be disconnected before making connections to prevent fire or injury.

Yes, all pipes must include a properly installed anti-siphon valve or anti-siphon loop to prevent water siphoning.

The Supersub 500 pump can be used as the primary or sole bilge pump in recreational boats up to 24 meters (78.8 feet). It is designed for the bilges of these vessels.

No, the Supersub product line is non-repairable. It is specifically stated not to unscrew the rear section, as any intervention on the internal electronics will render the pump unusable. In case of failure, the pump must be replaced.

Due to the extreme conditions encountered in boat bilges (temperature changes, varied chemical environments), it is recommended to replace your submersible bilge pump at least every 3 years.

No, the SS5012 model of the Supersub 500 bilge pump is a standard pump that requires a separate bilge switch for activation. It is not automatic by default.

However, it can be made automatic by pairing it with external accessories, such as an electronic water-activated switch (references BE9003 or BE9006) or a float switch (reference BE9002), which are available separately.

For correct installation of the Whale Supersub 500 (SS5012) bilge pump, the following points are critical:

Mounting: The pump must be mounted on a bulkhead or an additional board with a minimum thickness of 19 mm (3/4"). It is essential not to screw it directly to the boat's hull. Water discharge: Pumped water must be discharged through a through-hull fitting located above the boat's waterline. All hoses must include a properly installed non-return valve or anti-siphon loop. Non-return valve: It is highly recommended to use a non-return valve (reference LV1219) with the SS5012 model for optimal performance. Electrical power: Wiring must comply with applicable electrical standards and include a properly rated fuse or circuit breaker to prevent fire risk.